arXiv subjects

Kejun Zhu

Publications and source records attributed to Kejun Zhu.

10 recordsLinked to original sources

arXiv2025

JUNO 20-inch PMT and electronics system characterization using large pulses of PMT dark counts at the Pan-Asia testing platform

The main goal of the JUNO experiment is to determine the neutrino mass ordering with a 20kt liquid-scintillator detector. The 20-inch PMT and its 1F3 (one for three) electronics are crucial to realize the excellent energy resolution of at least 3% at 1MeV. The knowledge on the PMT and 1F3 electronics response is critical for detector performance understanding. A study of the JUNO 20-inch PMT and 1F3 electronics system characterization is presented using large pulses of PMT dark count at the Pan-Asia testing platform in China. Thanks to its broad amplitude range and high rate, the large pulse signals are also used to investigate the PMT after pulse response.

physics.ins-det↗

arXiv2024

Design and Implementation of TAO DAQ System

Purpose: The Taishan Antineutrino Observatory (TAO) is a satellite experiment of the Jiangmen Underground Neutrino Observatory (JUNO), also known as JUNO-TAO. Located close to one of the reactors of the Taishan Nuclear Power Plant, TAO will measure the antineutrino energy spectrum precisely as a reference spectrum for JUNO. The data acquisition (DAQ) system is designed to acquire data from the TAO readout electronics and process it with software trigger and data compression algorithms. The data storage bandwidth is limited by the onsite network to be less than 100 Mb/s. Methods: The system is designed based on a distributed architecture, with fully decoupled modules to facilitate customized design and implementation. It is divided into two main components: the data flow system and the online software. The online software serves as the foundation, providing the electronics configuration, the process management, the run control, and the information sharing. The data flow system facilitates continuous data acquisition from various electronic boards or trigger systems, assembles and processes raw data, and ultimately stores it on the disk. Results: The core functionality of the system has been designed and developed. The usability of the data flow system interface and the software trigger results have been verified during the pre-installation testing phase. Conclusion: The DAQ system has been deployed for the TAO experiment. It has also successfully been applied to the integration test of the detector and electronics prototypes.

physics.ins-det↗

arXiv2022

Check on the features of potted 20-inch PMTs with 1F3 electronics prototype at Pan-Asia

The Jiangmen underground neutrino observatory (JUNO) is a neutrino project with a 20-kton liquid scintillator detector located at 700-m underground. The large 20-inch PMTs are one of the crucial components of the JUNO experiment aiming to precision neutrino measurements with better than 3% energy resolution at 1 MeV. The excellent energy resolution and a large fiducial volume provide many exciting opportunities for addressing important topics in neutrino and astro-particle physics. With the container #D at JUNO Pan-Asia PMT testing and potting station, the features of waterproof potted 20-inch PMTs were measured with JUNO 1F3 electronics prototype in waveform and charge, which are valuable for better understanding on the performance of the waterproof potted PMTs and the JUNO 1F3 electronics. In this paper, basic features of JUNO 1F3 electronics prototype run at Pan-Asia will be introduced, followed by an analysis of the waterproof potted 20-inch PMTs and a comparison with the results from commercial electronics used by the container #A and #B.

physics.ins-det↗

arXiv2020

The study of calibration for the hybrid pixel detector with single photon counting in HEPS-BPIX

The calibration process for the hybrid array pixel detector designed for High Energy Photon Source in China, we called HEPS-BPIX, is presented in this paper. Based on the threshold scanning, the relationship between energy and threshold is quantified for the threshold calibration. For the threshold trimming, the precise algorithm basing on LDAC characteristic and fast algorithm basing on LDAC scanning are proposed in this paper to study the performance of the threshold DACs which will be applied to the pixel. The threshold dispersion has been reduced from 46.28 mV without algorithm to 6.78 mV with the precise algorithm, whereas it is 7.61 mV with fast algorithm. For the temperature from 5 to 60 , the threshold dispersion of precise algorithm varies in the range of about 5.69 mV, whereas it is about 33.21 mV with the fast algorithm which can be re-corrected to 1.49 mV. The measurement results show that the fast algorithm could get the applicable threshold dispersion for a silicon pixel module and take a shorter time, while the precise algorithm could get better threshold dispersion, but time consuming. The temperature dependence of the silicon pixel module noise is also studied to assess the detector working status. The minimum detection energy can be reduced about 0.83 keV at a 20 lower temperature.

physics.ins-det↗

arXiv2020

Measurement of the neutron beam profile of the Back-n white neutron facility at CSNS with a Micromegas detector

The Back-n white neutron beam line, which uses back-streaming white neutrons from the spallation target of the China Spallation Neutron Source, is used for nuclear data measurements. A Micromegas-based neutron detector with two variants was specially developed to measure the beam spot distribution for this beam line. In this article, the design, fabrication, and characterization of the detector are described. The results of the detector performance tests are presented, which include the relative electron transparency, the gain and the gain uniformity, and the neutron beam profile reconstruction capability. The result of the first measurement of the Back-n neutron beam spot distribution is also presented.

physics.ins-det↗

arXiv2019

Measurements of differential and angle-integrated cross sections for the $^{10}$B($n, α$)$^{7}$Li reaction in the neutron energy range from 1.0 eV to 2.5 MeV

Differential and angle-integrated cross sections for the $^{10}$B($n, α$)$^{7}$Li, $^{10}$B($n, α$$_{0}$)$^{7}$Li and $^{10}$B($n, α$$_{1}$)$^{7}$Li$^{*}$ reactions have been measured at CSNS Back-n white neutron source. Two enriched (90%) $^{10}$B samples 5.0 cm in diameter and ~85.0 $μ$g/cm$^{2}$ in thickness each with an aluminum backing were prepared, and back-to-back mounted at the sample holder. The charged particles were detected using the silicon-detector array of the Light-charged Particle Detector Array (LPDA) system. The neutron energy E$_{n}$ was determined by TOF (time-of-flight) method, and the valid $α$ events were extracted from the E$_{n}$-Amplitude two-dimensional spectrum. With 15 silicon detectors, the differential cross sections of $α$-particles were measured from 19.2° to 160.8°. Fitted with the Legendre polynomial series, the ($n, α$) cross sections were obtained through integration. The absolute cross sections were normalized using the standard cross sections of the $^{10}$B($n, α$)$^{7}$Li reaction in the 0.3 - 0.5 MeV neutron energy region. The measurement neutron energy range for the $^{10}$B($n, α$)$^{7}$Li reaction is 1.0 eV $\le$ En < 2.5 MeV (67 energy points), and for the $^{10}$B($n, α$$_{0}$)$^{7}$Li and $^{10}$B($n, α$$_{1}$)$^{7}$Li$^{*}$ reactions is 1.0 eV $\le$ En < 1.0 MeV (59 energy points). The present results have been analyzed by the resonance reaction mechanism and the level structure of the $^{11}$B compound system, and compared with existing measurements and evaluations.

nucl-ex↗

arXiv2018

An SOA Based Design of JUNO DAQ Online Software

The Online Software, manager of the JUNO data acquisition (DAQ) system, is composed of many distributed components working coordinately. It takes the responsibility of configuring, processes management, controlling and information sharing etc. The design of service-oriented architecture (SOA) which represents the modern tendency in the distributed system makes the online software lightweight, loosely coupled, reusable, modular, self-contained and easy to be extended. All the services in the SOA distributed online software system will send messages each to another directly without a traditional broker in the middle, which means that services could operate harmoniously and independently. ZeroMQ is chosen but not the only technical choice as the low-level communication middle-ware because of its high performance and convenient communication model while using Google Protocol Buffers as a marshaling library to unify the pattern of message contents. Considering the general requirement of JUNO, the concept of partition and segment are defined to ensure multiple small-scaled DAQs could run simultaneous and easy to join or leave. All running data except the raw physics events will be transmitted, processed and recorded to the database. High availability (HA) is also taken into account to solve the inevitable single point of failure (SPOF) in the distribution system. This paper will introduce all the core services' functionality and techniques in detail.

cs.SE↗

arXiv2018

JUNO DAQ Readout and Event Building Research

The Jiangmen Underground Neutrino Observatory(JUNO) experiment will develop an internationally leading neutrino experimental station to measure the order of neutrino mass and carry out many other scientific frontier studies. The entire experimental system includes the detector system, the electronics system, and the data acquisition (DAQ) system. Data flow is the core of JUNO DAQ system. Readout system and Event Building (EB) system are two key aspects of data flow. Based on the requirements analysis of JUNO DAQ, this paper proposes a data flow schema of distributed network readout and second-level event building. Focusing on the performance requirements of JUNO DAQ, the performance of the readout and event building module, the number of readout processes deployed on each node, and integration performance of the two modules are studied. The results of the research provide a reference for further optimization of the JUNO DAQ data flow framework

physics.ins-det↗

arXiv2016

First results of the new endcap TOF commissioning at BESIII

The upgrade of the current BESIII Endcap TOF (ETOF) is carried out with the Multi-gap Resistive Plate Chamber (MRPC) technology. The installation of the new ETOF has been finished in October 2015. The first results of the MRPCs commissioning at BESIII are reported in this paper.

physics.ins-det↗

arXiv2016

The cosmic ray test of MRPCs for the BESIII ETOF upgrade

In order to improve the particle identification capability of the Beijing Spectrometer III (BESIII),t is proposed to upgrade the current endcap time-of-flight (ETOF) detector with multi-gap resistive plate chamber (MRPC) technology. Aiming at extending ETOF overall time resolution better than 100ps, the whole system including MRPC detectors, new-designed Front End Electronics (FEE), CLOCK module, fast control boards and time to digital modules (TDIG), was built up and operated online 3 months under the cosmic ray. The main purposes of cosmic ray test are checking the detectors' construction quality, testing the joint operation of all instruments and guaranteeing the performance of the system. The results imply MRPC time resolution better than 100$ps$, efficiency is about 98$\%$ and the noise rate of strip is lower than 1$Hz/$($scm^{2}$) at normal threshold range, the details are discussed and analyzed specifically in this paper. The test indicates that the whole ETOF system would work well and satisfy the requirements of upgrade.

physics.ins-det↗