arXiv subjects

Michele Zorzi

Publications and source records attributed to Michele Zorzi.

At least 145 records · Page 8Linked to original sources

arXiv2019

On Optimal Policies in Full-Duplex Wireless Powered Communication Networks

The optimal resource allocation scheme in a full-duplex Wireless Powered Communication Network (WPCN) composed of one Access Point (AP) and two wireless devices is analyzed and derived. AP operates in a full-duplex mode and is able to broadcast wireless energy signals in downlink and receive information data in uplink simultaneously. On the other hand, each wireless device is assumed to be equipped with Radio-Frequency (RF) energy harvesting circuitry which gathers the energy sent by AP and stores it in a finite capacity battery. The harvested energy is then used for performing uplink data transmission tasks. In the literature, the main focus so far has been on slot-oriented optimization. In this context, all the harvested RF energy in a given slot is also consumed in the same slot. However, this approach leads to sub-optimal solutions because it does not take into account the Channel State Information (CSI) variations over future slots. Differently from most of the prior works, in this paper we focus on the long-term weighted throughput maximization problem. This approach significantly increases the complexity of the optimization problem since it requires to consider both CSI variations over future slots and the evolution of the batteries when deciding the optimal resource allocation. We formulate the problem using the Markov Decision Process (MDP) theory and show how to solve it. Our numerical results emphasize the superiority of our proposed full-duplex WPCN compared to the half-duplex WPCN and reveal interesting insights about the effects of perfect as well as imperfect self-interference cancellation techniques on the network performance.

cs.IT↗

arXiv2019

Bit Allocation for Increased Power Efficiency in 5G Receivers with Variable-Resolution ADCs

In future high-capacity wireless systems based on mmWave or massive multiple input multiple output (MIMO), the power consumption of receiver Analog to Digital Converters (ADC) is a concern. Although hybrid or analog systems with fewer ADCs have been proposed, fully digital receivers with many lower resolution ADCs (and lower power) may be a more versatile solution. In this paper, focusing on an uplink scenario, we propose to take the optimization of ADC resolution one step further by enabling variable resolutions in the ADCs that sample the signal received at each antenna. This allows to give more bits to the antennas that capture the strongest incoming signal and fewer bits to the antennas that capture little signal energy and mostly noise. Simulation results show that, depending on the unquantized link SNR, a power saving in the order of 20-80% can be obtained by our variable resolution proposal in comparison with a reference fully digital receiver with a fixed low number of bits in all its ADCs.

cs.IT↗

arXiv2019

Millimeter Wave Receiver Comparison Under Energy vs Spectral Efficiency Trade-off

Receivers for mmWave systems suffer from high power consumption in Analog to Digital Converters (ADC), and there is a need to compare the three major receiver architectures: Analog, Hybrid and Digital Combining (AC, HC and DC). Moreover, the specific power consumption figure of merit of ADCs varies significantly between different component designs in the literature, so that comparisons performed for one ADC model - no matter how representative of the state of the art - do not necessarily carry over to other ADC designs with different figures of merit. In this work, we formulate a comparison method between AC, HC and DC that can be easily reproduced with different power consumption parameters and provides all information for receiver architecture selection in a compact chart figure. We also present an interpretation of the receiver selection decision problem as a multi-objective utility optimization to find the best Spectral Efficiency (SE) versus Energy Efficiency (EE) trade-off. We use existing results on the achievable rate of AC, HC and DC systems and an Additive Quantization Noise Model (AQNM) of the ADC capacity degradation. For some example commercial component parameters, we show that the usually held belief that DC requires the highest power is not valid in many cases. Rather, either DC or HC alternatively result in the better SE vs EE trade-off depending strongly on the considered component parameters and on the weight assigned to SE vs EE in the utility maximization.

cs.IT↗

arXiv2019

Technical Report on Optimal Link Scheduling in Millimeter Wave Multi-hop Networks with Space Division Multiple Access and Multiplexing

In this paper we study the maximum throughput achievable with optimal scheduling in multi-hop networks with highly directive antenna arrays capable of Space Division Multiplexing (SDM) at the transmitter and Space Division Multiple Access (SDMA) at the receiver. This network model is relevant for future millimeter wave (mmWave) systems, which are expected to implement self-backhauled cellular networks with very high data rates, relying on carrier frequencies between 10-300 GHz, channels with a very large bandwidth, and a large number of antenna elements, even in mobile devices. We adapt mmWave channel propagation, antenna array and link rate models to the classic throughput-optimality and Network Utility Maximization (NUM) scheduling framework for multi-hop networks. Directional antenna gains, transmission towards multiple destinations at once, and simultaneous reception of signals from multiple sources, are all new characteristics not featured in the existing NUM literature. We verify that the classic NUM convergence lemmas are still valid under this new set of constraints, and discuss a series of algorithms to achieve or approximate the performance of the optimal Maximum Back Pressure (MBP) solution. Finally, our analysis serves as an estimation of the potential improvement in cellular network throughput capacity due to the integration of SDM/SDMA techniques and multi-hop.

cs.IT↗

arXiv2019

Stochastic Geometric Coverage Analysis in mmWave Cellular Networks with Realistic Channel and Antenna Radiation Models

Millimeter-wave (mmWave) bands will play an important role in 5G wireless systems. The system performance can be assessed by using models from stochastic geometry that cater for the directivity in the desired signal transmissions as well as the interference, and by calculating the signal-to-interference-plus-noise ratio (SINR) coverage. Nonetheless, the correctness of the existing coverage expressions derived through stochastic geometry may be questioned, as it is not clear whether they capture the impact of the detailed mmWave channel and antenna features. In this study, we propose an SINR coverage analysis framework that includes realistic channel model (from NYU) and antenna element radiation patterns (with isotropic/directional radiation). We first introduce two parameters, aligned gain and misaligned gain, associated with the desired signal beam and the interfering signal beam, respectively. We provide the distributions of the aligned and misaligned gains through curve fitting of system-simulation results. The distribution of these gains is used to determine the distribution of the SINR. We compare the obtained analytical SINR coverage with the corresponding SINR coverage calculated via system-level simulations. The results show that both aligned and misaligned gains can be modeled as exponential-logarithmically distributed random variables with the highest accuracy, and can further be approximated as exponentially distributed random variables with reasonable accuracy. These approximations are thus expected to be useful to evaluate the system performance under ultra-reliable and low-latency communication (URLLC) and evolved mobile broadband (eMBB) scenarios, respectively.

cs.NI↗

arXiv2018

Eco-friendly Power Cost Minimization for Geo-distributed Data Centers Considering Workload Scheduling

The rapid development of renewable energy in the energy Internet is expected to alleviate the increasingly severe power problem in data centers, such as the huge power costs and pollution. This paper focuses on the eco-friendly power cost minimization for geo-distributed data centers supplied by multi-source power, where the geographical scheduling of workload and temporal scheduling of batteries' charging and discharging are both considered. Especially, we innovatively propose the Pollution Index Function to model the pollution of different kinds of power, which can encourage the use of cleaner power and improve power savings. We first formulate the eco-friendly power cost minimization problem as a multi-objective and mixed-integer programming problem, and then simplify it as a single-objective problem with integer constraints. Secondly, we propose a Sequential Convex Programming (SCP) algorithm to find the globally optimal non-integer solution of the simplified problem, which is non-convex, and then propose a low-complexity searching method to seek for the quasi-optimal mixed-integer solution of it. Finally, simulation results reveal that our method can improve the clean energy usage up to 50\%--60\% and achieve power cost savings up to 10\%--30\%, as well as reduce the delay of requests.

cs.NI↗

arXiv2018

Fast HARQ over Finite Blocklength Codes: A Technique for Low-Latency Reliable Communication

This paper studies the performance of delay-constrained hybrid automatic repeat request HARQ protocols. Particularly, we propose a fast HARQ protocol where, to increase the end-to-end throughput, some HARQ feedback signals and successive message decodings are omitted. Considering quasi-static channels and a bursty communication model, we derive closed-form expressions for the message decoding probabilities as well as the throughput, the expected delay and the error probability of the HARQ setups. The analysis is based on recent results on the achievable rates of finite-length codes and shows the effect of the codeword length on the system performance. Moreover, we evaluate the effect of various parameters such as imperfect channel estimation and hardware on the system performance. As demonstrated, the proposed fast HARQ protocol reduces the packet transmission delay considerably, compared to state-of-the-art HARQ schemes. For example, with typical message decoding delay profiles and a maximum of 2,...,5 transmission rounds, the proposed fast HARQ protocol can improve the expected delay, compared to standard HARQ, by 27, 42, 52 and 60%, respectively, independently of the code rate/fading model.

cs.IT↗

arXiv2018

Will TCP work in mmWave 5G Cellular Networks?

The vast available spectrum in the millimeter wave (mmWave) bands offers the possibility of multi-Gbps data rates for fifth generation (5G) cellular networks. However, mmWave capacity can be highly intermittent due to the vulnerability of mmWave signals to blockages and delays in directional searching. Such highly variable links present unique challenges for adaptive control mechanisms in transport layer protocols and end-to-end applications. This paper considers the fundamental question of whether TCP - the most widely used transport protocol - will work in mmWave cellular systems. The paper provides a comprehensive simulation study of TCP considering various factors such as the congestion control algorithm, including the recently proposed TCP BBR, edge vs. remote servers, handover and multi- connectivity, TCP packet size and 3GPP-stack parameters. We show that the performance of TCP on mmWave links is highly dependent on different combinations of these parameters, and identify the open challenges in this area.

cs.NI↗

arXiv2018

A Spectrum Sharing Solution for the Efficient Use of mmWave Bands in 5G Cellular Scenarios

Regulators all around the world have started identifying the portions of the spectrum that will be used for the next generation of cellular networks. A band in the mmWave spectrum will be exploited to increase the available capacity. In response to the very high expected traffic demand, a sharing mechanism may make it possible to use the spectrum more efficiently. In this work, moving within the European and Italian regulatory conditions, we propose the use of Licensed Spectrum Access (LSA) to coordinate sharing among cellular operators. Additionally, we show some preliminary results on our research activities which are focused on a dynamic spectrum sharing approach applied in simulated 5G cellular scenarios.

cs.NI↗

arXiv2018

Multi-Sector and Multi-Panel Performance in 5G mmWave Cellular Networks

The next generation of cellular networks (5G) will exploit the mmWave spectrum to increase the available capacity. Communication at such high frequencies, however, suffers from high path loss and blockage, therefore directional transmissions using antenna arrays and dense deployments are needed. Thus, when evaluating the performance of mmWave mobile networks, it is necessary to accurately model the complex channel, the directionality of the transmission, but also the interplay that these elements can have with the whole protocol stack, both in the radio access and in the higher layers. In this paper, we improve the channel model abstraction of the mmWave module for ns-3, by introducing the support of a more realistic antenna array model, compliant with 3GPP NR requirements, and of multiple antenna arrays at the base stations and mobile handsets. We then study the end-to-end performance of a mmWave cellular network by varying the channel and antenna array configurations, and show that increasing the number of antenna arrays and, consequently, the number of sectors is beneficial for both throughput and latency.

cs.NI↗

arXiv2018

Low-latency Networking: Where Latency Lurks and How to Tame It

While the current generation of mobile and fixed communication networks has been standardized for mobile broadband services, the next generation is driven by the vision of the Internet of Things and mission critical communication services requiring latency in the order of milliseconds or sub-milliseconds. However, these new stringent requirements have a large technical impact on the design of all layers of the communication protocol stack. The cross layer interactions are complex due to the multiple design principles and technologies that contribute to the layers' design and fundamental performance limitations. We will be able to develop low-latency networks only if we address the problem of these complex interactions from the new point of view of sub-milliseconds latency. In this article, we propose a holistic analysis and classification of the main design principles and enabling technologies that will make it possible to deploy low-latency wireless communication networks. We argue that these design principles and enabling technologies must be carefully orchestrated to meet the stringent requirements and to manage the inherent trade-offs between low latency and traditional performance metrics. We also review currently ongoing standardization activities in prominent standards associations, and discuss open problems for future research.

eess.SP↗

arXiv2018

Towards Optimal Resource Allocation in Wireless Powered Communication Networks with Non-Orthogonal Multiple Access

The optimal allocation of time and energy resources is characterized in a Wireless Powered Communication Network (WPCN) with non-Orthogonal Multiple Access (NOMA). We consider two different formulations; in the first one (max-sum), the sum-throughput of all users is maximized. In the second one (max-min), and targeting fairness among users, we consider maximizing the min-throughput of all users. Under the above two formulations, two NOMA decoding schemes are studied, namely, low complexity decoding (LCD) and successive interference cancellation decoding (SICD). Due to the non-convexity of three of the studied optimization problems, we consider an approximation approach, in which the non-convex optimization problem is approximated by a convex optimization problem, which satisfies all the constraints of the original problem. The approximated convex optimization problem can then be solved iteratively. The results show a trade-off between maximizing the sum throughout and achieving fairness through maximizing the minimum throughput.

math.OC↗

arXiv2018

End-to-End Simulation of Integrated Access and Backhaul at mmWaves

Recently, the millimeter wave (mmWave) bands have been investigated as a means to support the foreseen extreme data rate demands of next-generation cellular networks (5G). However, in order to overcome the severe isotropic path loss and the harsh propagation experienced at such high frequencies, a dense base station deployment is required, which may be infeasible because of the unavailability of fiber drops to provide wired backhauling. To address this challenge, the 3GPP is investigating the concept of Integrated Access and Backhaul (IAB), i.e., the possibility of providing wireless backhaul to the mobile terminals. In this paper, we (i) extend the capabilities of the existing mmWave module for ns-3 to support advanced IAB functionalities, and (ii) evaluate the end-to-end performance of the IAB architecture through system-level full-stack simulations in terms of experienced throughput and communication latency. We finally provide guidelines on how to design optimal wireless backhaul solutions in the presence of resource-constrained and traffic-congested mmWave scenarios.

cs.NI↗

arXiv2018

On the Feasibility of Integrating mmWave and IEEE 802.11p for V2V Communications

Recently, the millimeter wave (mmWave) band has been investigated as a means to support the foreseen extreme data rate demands of emerging automotive applications, which go beyond the capabilities of existing technologies for vehicular communications. However, this potential is hindered by the severe isotropic path loss and the harsh propagation of high-frequency channels. Moreover, mmWave signals are typically directional, to benefit from beamforming gain, and require frequent realignment of the beams to maintain connectivity. These limitations are particularly challenging when considering vehicle-to-vehicle (V2V) transmissions, because of the highly mobile nature of the vehicular scenarios, and pose new challenges for proper vehicular communication design. In this paper, we conduct simulations to compare the performance of IEEE 802.11p and the mmWave technology to support V2V networking, aiming at providing insights on how both technologies can complement each other to meet the requirements of future automotive services. The results show that mmWave-based strategies support ultra-high transmission speeds, and IEEE 802.11p systems have the ability to guarantee reliable and robust communications.

cs.NI↗

arXiv2018

Impact of Channel Models on the End-to-End Performance of mmWave Cellular Networks

Communication at mmWave frequencies is one of the major innovations of the fifth generation of cellular networks, because of the potential multi-gigabit data rate given by the large amounts of available bandwidth. The mmWave channel, however, makes reliable communications particularly challenging, given the harsh propagation environment and the sensitivity to blockage. Therefore, proper modeling of the mmWave channel is fundamental for accurate results in system simulations of mmWave cellular networks. Nonetheless, complex models, such as the 3GPP channel model for frequencies above 6 GHz, may introduce a significant overhead in terms of computational complexity. In this paper we investigate the trade offs related to the accuracy and the simplicity of the channel model in end-to-end network simulations, and the impact on the performance evaluation of transport protocols.

cs.NI↗

arXiv2018

Enabling LTE RACH Collision Multiplicity Detection via Machine Learning

The collision resolution mechanism in the Random Access Channel (RACH) procedure of the Long-Term Evolution (LTE) standard is known to represent a serious bottleneck in case of machine-type traffic. Its main drawbacks are seen in the facts that Base Stations (eNBs) typically cannot infer the number of collided User Equipments (UEs) and that collided UEs learn about the collision only implicitly, through the lack of the feedback in the later stage of the RACH procedure. The collided UEs then restart the procedure, thereby increasing the RACH load and making the system more prone to collisions. In this paper, we leverage machine learning techniques to design a system that outperforms the state-of-the-art schemes in preamble detection for the LTE RACH procedure. Most importantly, our scheme can also estimate the collision multiplicity, and thus gather information about how many devices chose the same preamble. This data can be used by the eNB to resolve collisions, increase the supported system load and reduce transmission latency. The presented approach is applicable to novel 3GPP standards that target massive IoT, e.g., LTE-M and NB-IoT.

cs.IT↗

arXiv2018

Performance Study of LTE and mmWave in Vehicle-to-Network Communications

A key enabler for the emerging autonomous and cooperative driving services is high-throughput and reliable Vehicle-to-Network (V2N) communication. In this respect, the millimeter wave (mmWave) frequencies hold great promises because of the large available bandwidth which may provide the required link capacity. However, this potential is hindered by the challenging propagation characteristics of high-frequency channels and the dynamic topology of the vehicular scenarios, which affect the reliability of the connection. Moreover, mmWave transmissions typically leverage beamforming gain to compensate for the increased path loss experienced at high frequencies. This, however, requires fine alignment of the transmitting and receiving beams, which may be difficult in vehicular scenarios. Those limitations may undermine the performance of V2N communications and pose new challenges for proper vehicular communication design. In this paper, we study by simulation the practical feasibility of some mmWave-aware strategies to support V2N, in comparison to the traditional LTE connectivity below 6 GHz. The results show that the orchestration among different radios represents a viable solution to enable both high-capacity and robust V2N communications.

cs.NI↗

arXiv2018

Initial Access Frameworks for 3GPP NR at mmWave Frequencies

The use of millimeter wave (mmWave) frequencies for communication will be one of the innovations of the next generation of cellular mobile networks (5G). It will provide unprecedented data rates, but is highly susceptible to rapid channel variations and suffers from severe isotropic pathloss. Highly directional antennas at the transmitter and the receiver will be used to compensate for these shortcomings and achieve sufficient link budget in wide area networks. However, directionality demands precise alignment of the transmitter and the receiver beams, an operation which has important implications for control plane procedures, such as initial access, and may increase the delay of the data transmission. This paper provides a comparison of measurement frameworks for initial access in mmWave cellular networks in terms of detection accuracy, reactiveness and overhead, using parameters recently standardized by the 3GPP and a channel model based on real-world measurements. We show that the best strategy depends on the specific environment in which the nodes are deployed, and provide guidelines to characterize the optimal choice as a function of the system parameters.

cs.NI↗