arXiv subjects

Roberto Russo

Publications and source records attributed to Roberto Russo.

10 recordsLinked to original sources

arXiv2026

Giant Effective Permeability in Drude Thin Films Probed by THz Time-Domain Spectroscopy

The electromagnetic response of metallic films is commonly analyzed in terahertz spectroscopy by assuming unit relative magnetic permeability. In this work we show that this assumption introduces significant distortions in the electrodynamic retrieval of highly conductive films. Aluminum and copper films, 10 nm thick, were investigated by terahertz time-domain spectroscopy in both transmission and reflection configurations. By applying a self consistent retrieval method that independently determines the complex permittivity and permeability, we show that the Drude-type dielectric response is systematically accompanied by a permeability that strongly departs from unity. This deviation is intrinsically linked to the reactive impedance of the films, which clarifies the light induced onset of large screening currents within a transversally confined geometry. A phenomenological interpretation based on the Faraday Neumann Lenz mechanism and a lumped-element model of the film impedance accounts for the observed trends. These results indicate that the common assumption $\tilde{\mu}=1$ in non-magnetic Drude films can lead to an incomplete or biased electrodynamic characterization in the terahertz regime.

cond-mat.other↗

arXiv2026

Surface nanostructuring of NbTi superconducting thin-film resonators for enhanced cryogenic thermometry

The rising complexity of cutting-edge cryogenic systems is currently imposing challenging technical constraints to the monitoring of ultra-cold temperatures through standard commercially available sensors. Among different alternative technologies, superconducting microwave resonators have been recently investigated as ideal candidates for performing on-chip cryogenic thermometry, in reason of their intrinsically low power dissipation, typically large temperature sensitivities and excellent sub-mK resolution below 10 K. In such a framework, through this study we aim at demonstrating the possibility to enhance the temperature performance of superconducting microwave resonators by means of surface nanostructuring. More specifically, different arrays of nanogaps are strategically patterned on the inductive line of a 1.3 GHz planar resonator, by partially etching a Nb50Ti50 thin film, in order to tune the critical transition of the material and, therefore, increase the curvature of the fres(T) response. Although the presence of such weak-links introduces larger microwave losses, a 1.5 K decrease of TC is recorded, which directly translates into an enhancement of the temperature sensitivity by a factor 10, with respect to a reference non-nanostructured sensor. In particular, a maximum value of dfres/dT = 62 MHz/K, at 4.2 K, is achieved for the device showing the largest nanogap width of about 350 nm, demonstrating that the surface nanostructuring of superconducting thin-films can be effectively engineered to enhance the temperature response of microwave resonators for high-performance cryogenic thermometry. We believe that similar approaches might be investigated and, eventually, adopted for the near-future development of the next generation of low-temperature sensors.

physics.app-ph↗

arXiv2026

Review of prototypes developed in a 65 nm CMOS imaging technology in view of vertexing applications at a future lepton collider

The OCTOPUS project addresses the development and characterization of monolithic active pixel sensors in the TPSCo 65 nm ISC technology in view of vertexing applications at a future lepton collider. Meeting the corresponding requirements -- outlined in the ECFA detector road map -- will necessitate the simulation, design, and testing of prototypes and a demonstrator chip in this very process. This work reviews the literature on existing prototypes, summarizing their design characteristics, properties, and performance in charged-particle detection, and provides an overview of previous simulation efforts. The presented results suggest the feasibility of the endeavor while showcasing challenges, the need for further investigations, and providing a foundation for imminent design choices.

physics.ins-det↗

arXiv2025

Influence of Radiation and AC Coupling on Time Performance of Analog Pixels Test Structures in 65 nm CMOS technology

Monolithic Active Pixel Sensors (MAPS) in advanced CMOS imaging technologies are key to next-generation tracking systems for high-energy physics, where radiation hardness and precise vertex reconstruction are essential. As part of the ALICE ITS3 R&D program in synergy with the CERN R&D, we evaluated the performance of the Analog Pixel Test Structures (APTS) fabricated in the TPSCo 65 nm CMOS imaging process. The prototypes employ 10 um pitch pixels with a fast operational amplifier-based buffering stage at the output, enabling direct characterization of intrinsic sensor response. Beam tests with minimum ionizing particles assessed the timing and charge collection of DC- and AC-coupled designs, including devices exposed to 10^14 NIEL and 10^15 NIEL non ioninsing energy loss. DC-coupled sensors demonstrated stable performance, maintaining time resolution lower than 70 ps and >99% detection efficiency up to 10^15 NIEL. AC-coupled sensors demonstrated a wide operational margin, with efficiencies above 99% for clusterization thresholds below 150 electrons. Even though the AC coupling allows higher reverse bias than DC-coupled sensors, the reduced signal amplitude lowers the signal-to-noise ratio, increasing the jitter contribution. At high reverse bias, the AC-coupled sensors achieve time resolutions comparable to the DC-coupled version, demonstrating the viability of both approaches. These results also suggest that combining the low capacitance of DC-coupled designs with the high-bias capability of AC coupling could further enhance time resolution. These results confirm the suitability of 65 nm MAPS for future collider detectors requiring high radiation tolerance, efficiency, and timing precision.

physics.ins-det↗

arXiv2025

Further Characterisation of Digital Pixel Test Structures Implemented in a 65 nm CMOS Process

The next generation of MAPS for future tracking detectors will have to meet stringent requirements placed on them. One such detector is the ALICE ITS3 that aims to be very light at 0.07% X/X$_{0}$ per layer and have a low power consumption in the active area of 40 mW/cm$^{2}$ by implementing wafer-scale MAPS bent into cylindrical half layers. To address these challenging requirements, the ALICE ITS3 project, in conjunction with the CERN EP R&D on monolithic pixel sensors, proposed the Tower Partners Semiconductor Co. 65 nm CMOS process as the starting point for the sensor. After the initial results confirmed the detection efficiency and radiation hardness, the choice of the technology was solidified by demonstrating the feasibility of operating MAPS in low-power consumption regimes, < 50 mW/cm$^{2}$, while maintaining high-quality performance. This was shown through a detailed characterisation of the Digital Pixel Test Structure (DPTS) prototype exposed to X-rays and ionising beams, and the results are presented in this article. Additionally, the sensor was further investigated through studies of the fake-hit rate, the linearity of the front-end in the range 1.7-28 keV, the performance after ionising irradiation, and the detection efficiency of inclined tracks in the range 0-45$^\circ$.

physics.ins-det↗

arXiv2025

Effects of the thin-film thickness on superconducting NbTi microwave resonators for on-chip cryogenic thermometry

Superconducting microwave resonators have recently gained a primary importance in the development of cryogenic applications, such as circuit quantum electrodynamics, electron spin resonance spectroscopy and particles detection for high-energy physics and astrophysics. In this work, we investigate the influence of the film thickness on the temperature response of microfabricated Nb50Ti50 superconducting resonators. S-shaped split ring resonators (S-SRRs), 20 nm to 150 nm thick, are designed to be electromagnetically coupled with standard Cu coplanar waveguides (CPWs) and their microwave properties are characterized at temperatures below 10 K. The combined contributions of the kinetic inductance LK(T) increase and the decreasing loaded quality factor QL, for thinner films, induce an optimum condition on the temperature sensitivity and resolution of the resonators. A noise equivalent temperature (NET) as low as 0.5 uK/Hz^(1/2), at 1 Hz, is reported for 100 nm thick resonators at 4.2 K. We also asses the possibility of implementing a multiplexed frequency readout, allowing for the simultaneous temperature tracking of several sensors along a single CPW. Such results demonstrate the possibility to perform a distributed cryogenic temperature monitoring, with a sub-mK resolution. Thus, the application of superconducting S-SRRs, eventually benefiting from an even higher LK(T), for a further miniaturization, as well as a back-end integration directly on-chip, can be envisioned for the accurate monitoring of localized temperature of devices operating in cryogenic conditions.

physics.app-ph↗

arXiv2025

Detection efficiency and spatial resolution of Monolithic Active Pixel Sensors bent to different radii

Bent monolithic active pixel sensors are the basis for the planned fully cylindrical ultra low material budget tracking detector ITS3 of the ALICE experiment. This paper presents results from testbeam campaigns using high-energy particles to verify the performance of 50 um thick bent ALPIDE chips in terms of efficiency and spatial resolution. The sensors were bent to radii of 18, 24 and 30 mm, slightly smaller than the foreseen bending radii of the future ALICE ITS3 layers. An efficiency larger than $99.9\%$ and a spatial resolution of approximately 5 um, in line with the nominal operation of flat ALPIDE sensors, is obtained at nominal operating conditions. These values are found to be independent of the bending radius and thus constitute an additional milestone in the demonstration of the feasibility of the planned ITS3 detector. In addition, a special geometry in which the beam particles graze the chip and traverse it laterally over distances of up to 3 mm is investigated.

physics.ins-det↗

arXiv2024

Time performance of Analog Pixel Test Structures with in-chip operational amplifier implemented in 65 nm CMOS imaging process

In the context of the CERN EP R&D on monolithic sensors and the ALICE ITS3 upgrade, the Tower Partners Semiconductor Co (TPSCo) 65 nm process has been qualified for use in high energy physics, and adopted for the ALICE ITS3 upgrade. An Analog Pixel Test Structure (APTS) featuring fast per pixel operational-amplifier-based buffering for a small matrix of four by four pixels, with a sensor with a small collection electrode and a very non-uniform electric field, was designed to allow detailed characterization of the pixel performance in this technology. Several variants of this chip with different pixel designs have been characterized with a (120 GeV/$c$) positive hadron beam. This result indicates that the APTS-OA prototype variants with the best performance achieve a time resolution of 63 ps with a detection efficiency exceeding 99% and a spatial resolution of 2 $\mu$m, highlighting the potential of TPSCo 65nm CMOS imaging technology for high-energy physics and other fields requiring precise time measurement, high detection efficiency, and excellent spatial resolution.

physics.ins-det↗

arXiv2022

Digital Pixel Test Structures implemented in a 65 nm CMOS process

The ALICE ITS3 (Inner Tracking System 3) upgrade project and the CERN EP R&D on monolithic pixel sensors are investigating the feasibility of the Tower Partners Semiconductor Co. 65 nm process for use in the next generation of vertex detectors. The ITS3 aims to employ wafer-scale Monolithic Active Pixel Sensors thinned down to 20 to 40 um and bent to form truly cylindrical half barrels. Among the first critical steps towards the realisation of this detector is to validate the sensor technology through extensive characterisation both in the laboratory and with in-beam measurements. The Digital Pixel Test Structure (DPTS) is one of the prototypes produced in the first sensor submission in this technology and has undergone a systematic measurement campaign whose details are presented in this article. The results confirm the goals of detection efficiency and non-ionising and ionising radiation hardness up to the expected levels for ALICE ITS3 and also demonstrate operation at +20 C and a detection efficiency of 99% for a DPTS irradiated with a dose of $10^{15}$ 1 MeV n$_{\mathrm{eq}}/$cm$^2$. Furthermore, spatial, timing and energy resolutions were measured at various settings and irradiation levels.

physics.ins-det↗

arXiv2013

Superconducting flux-flow type ultra-low-noise magnetic sensors - An alternative to dc-SQUIDs

A superconducting magnetometers based on the magnetic field dependence of the Eck step voltage in long Josephson tunnel junctions (LJTJs) is demonstrated. The field to be measured is applied perpendicular to a continuous superconducting pickup loop. Wherever the loop has a narrow constriction, the density of the flux-restoring circulating currents will become relatively high and will locally create a magnetic field large enough to bring a biased LJTJ in the flux-flow state, i.e., at a finite voltage proportional to the field strength. This method allows the realization of a novel family of robust and general-purpose superconducting devices which, despite their simplicity, function as ultra-low-noise, wide-band and high-dynamics magnetometers. The performances of low-T$_c$ sensor prototypes, among which a highly linear voltage responsivity and a magnetic spectral density $S_B^{1/2}< 3\,fT/Hz^{1/2}$, promise to be competitive with those of the best superconducting quantum interference devices.

cond-mat.mes-hall↗