arXiv subjects

Sergey Rumyantsev

Publications and source records attributed to Sergey Rumyantsev.

At least 19 recordsLinked to original sources

arXiv2026

A Quieter State of Charge -- Ultra-Low-Noise Collective Current in Charge-Density-Wave Nanowires

Electronic flicker noise limits phase stability in communication systems, reduces the sensitivity and selectivity of sensors, and degrades coherence in quantum devices. There is a strong need for unconventional materials and strategies for achieving ultra-low-noise performance in nanoscale and quantum electronics. Here, we demonstrate that in nanowires of the quasi-one-dimensional, fully gapped charge-density-wave material (TaSe4)2I, low-frequency electronic noise is suppressed below the limit of thermalized charge carriers in passive resistors. When the current is dominated by the sliding Frohlich condensate, the normalized noise spectral density decreases linearly with current, I -- a striking departure from the constant value observed in conventional conductors. No residual minimum noise level is reached for the current of the electron-lattice condensate in (TaSe4)2I nanowires. Repeating the measurements for another charge-density wave conductor, NbS3-II, we found a similar reduction below the normal electron limit at room temperature. Our findings signal intrinsically lower current fluctuations within a correlated electron transport regime.

cond-mat.str-el↗

arXiv2024

Temperature and Electron Concentration Dependences of 1/f Noise in Hg$_{1-x}$Cd$_x$Te -- Evidence for a Mobility Fluctuations Mechanism

Hg$_{1-x}$Cd$_x$Te is a unique material with the band-gap tunable by the temperature, pressure, and cadmium content in a wide range, from 1.6 eV to inverted band-gap of -0.3 eV. This makes Hg$_{1-x}$Cd$_x$Te one of the key materials for infrared and terahertz detectors, whose characteristics largely depend on the material noise properties. In this work, we investigated the low-frequency 1/f noise in a thick (800 nm) HgCdTe layer and in a field effect transistor (FET) with an 8 nm wide HgTe quantum well. Both structures exhibited a small contribution from contact noise and showed weak noise dependences on temperature. Investigation of the 1/f noise in HgTe quantum well FET as a function of gate voltage revealed that the noise also depends weakly on electron concentration. These findings indicate that the noise properties of Hg$_{1-x}$Cd$_x$Te are similar to those of graphene, where mobility fluctuations were found to be the dominant mechanism of the 1/f noise.

cond-mat.mes-hall↗

arXiv2023

The Noise of the Charge Density Waves in NbSe$_3$ Nanowires -- Contributions of Electrons and Quantum Condensate

Low-frequency electronic noise in charge-density-wave van der Waals materials has been an important characteristic, providing information about the material quality, phase transitions, and collective current transport. However, the noise sources and mechanisms have not been completely understood, particularly for the materials with a non-fully gapped Fermi surface where the electrical current includes components from individual electrons and the sliding charge-density wave. We investigated noise in nanowires of quasi-one-dimensional NbSe$_3$, focusing on a temperature range near the Pearls transition ~ 145 K. The data analysis allowed us to separate the noise produced by the individual conduction electrons and the quantum condensate of the charge density waves before and after the onset of sliding. The noise as a function of temperature and electric bias reveals several intriguing peaks. We explained the observed features by the depinning threshold field, the creep and sliding of the charge density waves, and the possible existence of the hidden phases. It was found that the charge density wave condensate is particularly noisy at the moment of depinning. The noise of the collective current reduces with the increasing bias voltage in contrast to the noise of the individual electrons. Our results shed light on the behavior of the charge density wave quantum condensate and demonstrate the potential of noise spectroscopy for investigating the properties of low-dimensional quantum materials.

cond-mat.mtrl-sci↗

arXiv2023

Conductance Fluctuations and Domain Depinning in Quasi-2D Charge-Density-Wave 1T-TaS$_2$ Thin Films

We investigated the temperature dependence of the conductance fluctuations in thin films of the quasi-two-dimensional 1T-TaS$_2$ van der Waals material. The conductance fluctuations, determined from the derivative current-voltage characteristics of two-terminal 1T-TaS$_2$ devices, appear prominently at the electric fields that correspond to the transitions between various charge-density-wave macroscopic quantum condensate phases and at the onset of the depinning of the charge density wave domains. The depinning threshold field, $E_D$, monotonically increases with decreasing temperature within the nearly commensurate charge-density-wave phase. The $E_D$ value increases with the decreasing 1T-TaS$_2$ film thickness, revealing the surface pinning of the charge density waves. Our analysis suggests that depinning is absent in the commensurate phase. It is induced by the electric field but facilitated by local heating. The measured trends for $E_D$ of the domain depinning are important for understanding the physics of charge density waves in quasi-two-dimensional crystals and for developing electronic devices based on this type of quantum materials.

cond-mat.mes-hall↗

arXiv2023

Low-Frequency Electronic Noise in the Aluminum Gallium Oxide Schottky Barrier Diodes

We report on the low-frequency electronic noise in (Al$_x$Ga$_{1-x}$)$_2$O$_3$ Schottky barrier diodes. The noise spectral density reveals 1/f dependence, characteristic of the flicker noise, with superimposed Lorentzian bulges at the intermediate current levels (f is the frequency). The normalized noise spectral density in such diodes was determined to be on the order of 10$^{-12}$ cm$^2$/Hz (f=10 Hz) at 1 A/cm$^2$ current density. At the intermediate current regime, we observed the random telegraph signal noise, correlated with the appearance of Lorentzian bulges in the noise spectrum. The random telegraph signal noise was attributed to the defects near the Schottky barrier. The defects can affect the local electric field and the potential barrier, and correspondingly, impact the electric current. The obtained results help to understand noise in Schottky barrier diodes made of ultra-wide-band-gap semiconductors and can be used for the material and device quality assessment.

cond-mat.mtrl-sci↗

arXiv2022

Low-Frequency Noise in Quasi-1D (TaSe$_4$)$_2$I Weyl Semimetal Nanoribbons

We report on low-frequency current fluctuations, i.e. electronic noise, in quasi-one-dimensional (TaSe$_4$)$_2$I Weyl semimetal nanoribbons. It was found that the noise spectral density is of the 1/f type and scales with the square of the current, S~I^2 (f is the frequency). The noise spectral density increases by almost an order of magnitude and develops Lorentzian features near the temperature T~225 K. These spectral changes were attributed to the charge-density-wave phase transition even though the temperature of the noise maximum deviates from the reported Peierls transition temperature in bulk (TaSe$_4$)$_2$I crystals. The noise level, normalized by the channel area, in these Weyl semimetal nanoribbons was surprisingly low, $\sim 10^{-9}$ um$^2$Hz$^{-1}$ at f=10 Hz, when measured below and above the Peierls transition temperature. Obtained results shed light on the specifics of electron transport in quasi-1D topological Weyl semimetals and can be important for their proposed applications as downscaled interconnects.

cond-mat.mes-hall↗

arXiv2022

Electrical Gating of the Charge-Density-Wave Phases in Quasi-2D h-BN/1T-TaS$_2$ Devices

We report on electrical gating of the charge-density-wave phases and current in h-BN capped three-terminal 1T-TaS$_2$ heterostructure devices. It is demonstrated that the application of a gate bias can shift the source-drain current-voltage hysteresis associated with the transition between the nearly commensurate and incommensurate charge-density wave phases. The evolution of the hysteresis and the presence of abrupt spikes in the current while sweeping the gate voltage suggest that the effect is electrical rather than self-heating. We attribute the gating to an electric-field effect on the commensurate charge-density-wave domains in the atomic planes near the gate dielectric. The transition between the nearly commensurate and incommensurate charge-density-wave phases can be induced by both the source-drain current and the electrostatic gate. Since the charge-density-wave phases are persistent in 1T-TaS2 at room temperature, one can envision memory applications of such devices when scaled down to the dimensions of individual commensurate domains and few-atomic plane thicknesses.

physics.app-ph↗

arXiv2021

Excess Noise in High-Current Diamond Diodes -- Physical Mechanisms and Implications for Reliability Assessment

We report results of an investigation of low-frequency excess noise in high-current diamond diodes. It was found that the electronic excess noise of the diamond diodes is dominated by generation - recombination noise, which reveals itself either as Lorentzian spectral features or as a 1/f noise spectrum (f is the frequency). The generation - recombination bulges are characteristic for diamond diodes with lower turn-on voltages. The noise spectral density dependence on forward current, I, reveals three distinctive regions in all examined devices - it scales as I^2 at the low (I<10 uA) and high (I>10 mA) currents, and, rather unusually, remain nearly constant at the intermediate current range. The characteristic trap time constants, extracted from the noise data, reveal a uniquely strong dependence on current. Interestingly, the performance of the diamond diodes improves with increasing temperature. The obtained results are important for development of noise spectroscopy-based approaches for device reliability assessment for the high-power diamond electronics.

physics.app-ph↗

arXiv2021

Low-Frequency Noise Characteristics of GaN Vertical PIN Diodes -- Effects of Current and Temperature

We report low-frequency noise characteristics of vertical GaN PIN diodes, focusing on the effects of the diode design, current and temperature. The as-grown and regrown diodes, with and without surface treatment have been studied. The noise in most of the GaN devices had a characteristic 1/f spectrum at high and moderate currents, while some devices revealed generation-recombination bulges at low currents (f is the frequency). The predominant trend of the noise spectral density, S, dependence on the current was S ~ I. All tested GaN PIN diodes had rather low normalized noise spectral densities of 10^-18 cm2/Hz -- 10^-16 cm2/Hz (f=10 Hz) at the current density J=1 A/cm2 at room temperature. The noise temperature dependences at different currents revealed peaks at T=375 K -- 400 K. Temperature, current, and frequency dependences of noise suggest that the noise mechanism is of the recombination origin. We argue that the noise measurements at low currents can be used to efficiently assess the quality of GaN PIN diodes.

cond-mat.mtrl-sci↗

arXiv2021

Nature of the 1/f Noise in Graphene, Direct Evidence for the Mobility Fluctuations Mechanism

The nature of the low-frequency current fluctuations, i.e. carrier number vs. mobility, defines the strategies for noise reduction in electronic devices. While the 1/f noise in metals has been attributed to the electron mobility fluctuations, the direct evidence is lacking (f is the frequency). Here we measured noise in h-BN encapsulated graphene transistor under the condition of geometrical magnetoresistance to directly assess the mechanism of low-frequency electronic current fluctuations. It was found that the relative noise spectral density of the graphene resistance fluctuations depends non-monotonically on the magnetic field (B) with a minimum at approximately uB=1 (u is the electron mobility). This observation proves unambiguously that the mobility fluctuations are the dominant mechanism of the electronic noise in high-quality graphene. Our results are important for all proposed applications of graphene in electronics and add to the fundamental understanding of the 1/f noise origin in any electronic device.

cond-mat.mes-hall↗

arXiv2021

Efficient Absorption of Terahertz Radiation in Graphene Polymer Composites

We demonstrate that polymer composites with a low loading of graphene, below 1.2 wt. %, are efficient as electromagnetic absorbers in the THz frequency range. The epoxy-based graphene composites were tested at frequencies from 0.25 THz to 4 THz, revealing total shielding effectiveness of 85 dB (1 mm thickness) with graphene loading of 1.2 wt. % at the frequency f=1.6 THz. The THz radiation is mostly blocked by absorption rather than reflection. The efficiency of the THz radiation shielding by the lightweight, electrically insulating composites, increases with increasing frequency. Our results suggest that even the thin-film or spray coatings of graphene composites with thickness in the few-hundred-micrometer range can be sufficient for blocking THz radiation in many practical applications.

physics.app-ph↗

arXiv2021

Low-Frequency Electronic Noise Spectroscopy of Quasi-2D van der Waals Antiferromagnetic Semiconductors

We investigated low-frequency current fluctuations, i.e. noise, in the quasi-two-dimensional (2D) van der Waals antiferromagnetic semiconductor FePS3 with the electronic bandgap of 1.5 eV. The electrical and noise characteristics of the p-type, highly resistive, thin films of FePS3 were measured at different temperatures. The noise spectral density was of the 1/f - type over most of the examined temperature range but revealed well-defined Lorentzian bulges, and increased strongly near the Neel temperature of 118 K (f is the frequency). Intriguingly, the noise spectral density attained its minimum at temperature T~200 K, which was attributed to an interplay of two opposite trends in noise scaling - one for semiconductors and another for materials with the phase transitions. The Lorentzian corner frequencies revealed unusual dependence on temperature and bias voltage, suggesting that their origin is different from the generation - recombination noise in conventional semiconductors. The obtained results are important for proposed applications of antiferromagnetic semiconductors in spintronic devices. They also attest to the power of the noise spectroscopy for monitoring various phase transitions.

cond-mat.mtrl-sci↗

arXiv2021

Electrically-Insulating Flexible Films with Quasi-One-Dimensional van-der-Waals Fillers as Efficient Electromagnetic Shields

We report polymer composite films containing fillers comprised of quasi-one-dimensional (1D) van der Waals materials, specifically transition metal trichalcogenides containing 1D structural motifs that enable their exfoliation into bundles of atomic threads. These nanostructures are characterized by extremely large aspect ratios of up to 10^6. The polymer composites with low loadings of quasi-1D TaSe3 fillers (below 3 vol. %) revealed excellent electromagnetic interference shielding in the X-band GHz and EHF sub-THz frequency ranges, while remaining DC electrically insulating. The unique electromagnetic shielding characteristics of these films are attributed to effective coupling of the electromagnetic waves to the high-aspect-ratio electrically-conductive TaSe3 atomic-thread bundles even when the filler concentration is below the electrical percolation threshold. These novel films are promising for high-frequency communication technologies, which require electromagnetic shielding films that are flexible, lightweight, corrosion resistant, electrically insulating and inexpensive.

cond-mat.mes-hall↗

arXiv2020

Graphene Composites as Efficient Electromagnetic Absorbers in the Extremely High Frequency Band

We report on the synthesis of the epoxy-based composites with graphene fillers and testing their electromagnetic shielding efficiency by the quasi-optic free-space method in the extremely high frequency (EHF) band (220 - 325 GHz). The curing adhesive composites were produced by a scalable technique with a mixture of single-layer and few-layer graphene layers of a few-micron lateral dimensions. It was found that the electromagnetic transmission, T, is low even at small concentrations of graphene fillers: T<1% at frequency of 300 GHz for a composite with only 1 wt% of graphene. The main shielding mechanism in composites with the low graphene loading is absorption. The composites of 1 mm thickness and graphene loading of 8 wt% provide excellent electromagnetic shielding of 70 dB in the sub-terahertz EHF frequency with negligible energy reflection to the environment. The developed lightweight adhesive composites with graphene fillers can be used as electromagnetic absorbers in the high-frequency microwave radio relays, microwave remote sensors, millimeter wave scanners, and wireless local area networks.

physics.app-ph↗

arXiv2020

Current Oscillations in Quasi-2D Charge-Density-Wave 1T-TaS2 Devices: Revisiting the "Narrow Band Noise" Concept

We report on current oscillations in quasi two-dimensional (2D) 1T-TaS2 charge-density-wave devices. The MHz-frequency range of the oscillations and the linear dependence of the frequency of the oscillations on the current resemble closely the "narrow band noise," which was often observed in the classical bulk quasi-one-dimensional (1D) trichalcogenide charge-density-wave materials. In bulk quasi-1D materials, the "narrow band noise" was interpreted as a direct evidence of the charge-density-wave sliding. Despite the similarities, we argue that the nature of the MHz oscillations in quasi-2D 1T-TaS2 is different from the "narrow band noise." Analysis of the biasing conditions and current indicate that the observed oscillations are related to the current instabilities due to the voltage-induced transition from the nearly commensurate to incommensurate charge-density-wave phase.

cond-mat.mes-hall↗

arXiv2019

Amplitude and Phase Noise of Magnons

The low-frequency amplitude and phase noise spectra of magnetization waves, i.e. magnons, was measured in the yttrium iron garnet (YIG) waveguides. This type of noise, which originates from the fluctuations of the physical properties of the YIG crystals, has to be taken into account in the design of YIG-based RF generators and magnonic devices for data processing, sensing and imaging applications. It was found that the amplitude noise level of magnons depends strongly on the power level, increasing sharply at the on-set of nonlinear dissipation. The noise spectra of both the amplitude and phase noise have the Lorentzian shape with the characteristic frequencies below 100 Hz.

physics.app-ph↗

arXiv2019

Low-Frequency Noise in Low-Dimensional van der Waals Materials

The emergence of graphene and two-dimensional van der Walls materials renewed interest to investigation of the low-frequency noise in the low-dimensional systems. The layered van der Waals materials offers unique opportunities for studying the low-frequency noise owing to the properties controlled by the thickness of these materials, and tunable carrier concentration. In this review, we describe unusual low-frequency noise phenomena in quasi-2D and quasi-1D van der Waals materials. We also demonstrate that the low-frequency noise spectroscopy is a powerful tool for investigation of the electron transport and charge-density-wave phase transitions in this class of materials.

cond-mat.mes-hall↗

arXiv2019

Low-Frequency Electronic Noise in Superlattice and Random-Packed Thin Films of Colloidal Quantum Dots

We report measurements of low-frequency electronic noise in ordered superlattice, weakly-ordered and random-packed thin films of 6.5 nm PbSe quantum dots prepared using several different ligand chemistries. For all samples, the normalized noise spectral density of the dark current revealed a Lorentzian component, reminiscent of the generation-recombination noise, superimposed on the 1/f background (f is the frequency). An activation energy of 0.3 eV was extracted from the temperature dependence of the noise spectra. The noise level in the ordered films was lower than that in the weakly-ordered and random-packed films. A large variation in the magnitude of the noise spectral density was also observed in samples with different ligand treatments. The obtained results are important for application of colloidal quantum dot films in photodetectors.

cond-mat.mes-hall↗