arXiv subjects

Eric Pop

Publications and source records attributed to Eric Pop.

At least 73 records · Page 4Linked to original sources

arXiv2020

Graphene-Based Electromechanical Thermal Switches

Thermal management is an important challenge in modern electronics, avionics, automotive, and energy storage systems. While passive thermal solutions (like heat sinks or heat spreaders) are often used, actively modulating heat flow (e.g. via thermal switches or diodes) would offer additional degrees of control over the management of thermal transients and system reliability. Here we report the first thermal switch based on a flexible, collapsible graphene membrane, with low operating voltage, < 2 V. We also employ active-mode scanning thermal microscopy (SThM) to measure the device behavior and switching in real time. A compact analytical thermal model is developed for the general case of a thermal switch based on a double-clamped suspended membrane, highlighting the thermal and electrical design challenges. System-level modeling demonstrates the thermal trade-offs between modulating temperature swing and average temperature as a function of switching ratio. These graphene-based thermal switches present new opportunities for active control of fast (even nanosecond) thermal transients in densely integrated systems.

cond-mat.mtrl-sci↗

arXiv2020

Ultrahigh Doping of Graphene Using Flame-Deposited MoO3

The expected high performance of graphene-based electronics is often hindered by lack of adequate doping, which causes low carrier density and large sheet resistance. Many reported graphene doping schemes also suffer from instability or incompatibility with existing semiconductor processing. Here we report ultrahigh and stable p-type doping up to ~7x10^13 1/cm^2 (~2x10^21 1/cm^3}) of monolayer graphene grown by chemical vapor deposition. This is achieved by direct polycrystalline MoO3 growth on graphene using a rapid flame synthesis technique. With this approach, the metal-graphene contact resistance for holes is reduced to ~200 Ohm-um. We also demonstrate that flame-deposited MoO3 provides over 5x higher doping of graphene, as well as superior thermal and long-term stability, compared to electron-beam deposited MoO3.

cond-mat.mes-hall↗

arXiv2020

Dynamic hybrid metasurfaces

Efficient hybrid plasmonic-photonic metasurfaces that simultaneously take advantage of the potential of both pure metallic and all-dielectric nanoantennas are identified as an emerging technology in flat optics. Nevertheless, post-fabrication tunable hybrid metasurfaces are still elusive. Here, we present a reconfigurable hybrid metasurface platform by incorporating the phase-change material Ge$_{2}$Sb$_{2}$Te$_{5}$ (GST) into metal-dielectric meta-atoms for active and non-volatile tuning of properties of light. We systematically design a reduced-dimension meta-atom, which selectively controls the fundamental hybrid plasmonic-photonic resonances of the metasurface via the dynamic change of optical constants of GST without compromising the scattering efficiency. As a proof-of-concept, we experimentally demonstrate miniaturized tunable metasurfaces that control the amplitude and phase of incident light necessary for high-contrast optical switching and anomalous to specular beam deflection, respectively. Finally, we leverage a deep learning-based approach to present an intuitive low-dimensional visualization of the enhanced range of response reconfiguration enabled by the addition of GST. Our findings further substantiate dynamically tunable hybrid metasurfaces as promising candidates for the development of small-footprint energy harvesting, imaging, and optical signal processing devices.

physics.optics↗

arXiv2020

Uncovering the Effects of Metal Contacts on Monolayer MoS2

Metal contacts are a key limiter to the electronic performance of two-dimensional (2D) semiconductor devices. Here we present a comprehensive study of contact interfaces between seven metals (Y, Sc, Ag, Al, Ti, Au, Ni, with work functions from 3.1 to 5.2 eV) and monolayer MoS2 grown by chemical vapor deposition. We evaporate thin metal films onto MoS2 and study the interfaces by Raman spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, transmission electron microscopy, and electrical characterization. We uncover that, 1) ultrathin oxidized Al dopes MoS2 n-type (> 2x10^12 1/cm^2) without degrading its mobility, 2) Ag, Au, and Ni deposition causes varying levels of damage to MoS2 (broadening Raman E' peak from <3 1/cm to >6 1/cm), and 3) Ti, Sc, and Y react with MoS2. Reactive metals must be avoided in contacts to monolayer MoS2, but control studies reveal the reaction is mostly limited to the top layer of multilayer films. Finally, we find that 4) thin metals do not significantly strain MoS2, as confirmed by X-ray diffraction. These are important findings for metal contacts to MoS2, and broadly applicable to many other 2D semiconductors.

cond-mat.mtrl-sci↗

arXiv2020

Reduced Thermal Conductivity of Supported and Encased Monolayer and Bilayer MoS$_2$

Electrical and thermal properties of atomically thin two-dimensional (2D) materials are affected by their environment, e.g. through remote phonon scattering or dielectric screening. However, while it is known that mobility and thermal conductivity (TC) of graphene are reduced on a substrate, these effects are much less explored in 2D semiconductors such as MoS$_2$. Here, we use molecular dynamics to understand TC changes in monolayer (1L) and bilayer (2L) MoS$_2$ by comparing suspended, supported, and encased structures. The TC of monolayer MoS$_2$ is reduced from ~117 Wm$^{-1}$K$^{-1}$ when suspended, to ~31 Wm$^{-1}$K$^{-1}$ when supported by SiO$_2$, at 300 K. Encasing 1L MoS$_2$ in SiO$_2$ further reduces its TC down to ~22 Wm$^{-1}$K$^{-1}$. In contrast, the TC of 2L MoS$_2$ is not as drastically reduced, being >50% higher than 1L both when supported and encased. These effects are due to phonon scattering with remote vibrational modes of the substrate, which are partly screened in 2L MoS$_2$. We also examine the TC of 1L MoS$_2$ across a wide range of temperatures (300 to 700 K) and defect densities (up to 5$\times$10$^{13}$ cm$^{-2}$), finding that the substrate reduces the dependence of TC on these factors. Taken together, these are important findings for all applications which will use 2D semiconductors supported or encased by insulators, instead of freely suspended.

cond-mat.mtrl-sci↗

arXiv2020

Temperature Dependent Thermal Boundary Conductance of Monolayer MoS$_2$ by Raman Thermometry

The electrical and thermal behavior of nanoscale devices based on two-dimensional (2D) materials is often limited by their contacts and interfaces. Here we report the temperature-dependent thermal boundary conductance (TBC) of monolayer MoS$_2$ with AlN and SiO$_2$, using Raman thermometry with laser-induced heating. The temperature-dependent optical absorption of the 2D material is crucial in such experiments, which we characterize here for the first time above room temperature. We obtain TBC ~ 15 MWm$^-$$^2$K$^-$$^1$ near room temperature, increasing as ~ T$^0$$^.$$^6$$^5$ in the range 300 - 600 K. The similar TBC of MoS$_2$ with the two substrates indicates that MoS$_2$ is the "softer" material with weaker phonon irradiance, and the relatively low TBC signifies that such interfaces present a key bottleneck in energy dissipation from 2D devices. Our approach is needed to correctly perform Raman thermometry of 2D materials, and our findings are key for understanding energy coupling at the nanoscale.

cond-mat.mes-hall↗

arXiv2019

Nonvolatile electrically reconfigurable integrated photonic switch

Reconfigurability of photonic integrated circuits (PICs) has become increasingly important due to the growing demands for electronic-photonic systems on a chip driven by emerging applications, including neuromorphic computing, quantum information, and microwave photonics. Success in these fields usually requires highly scalable photonic switching units as essential building blocks. Current photonic switches, however, mainly rely on materials with weak, volatile thermo-optic or electro-optic modulation effects, resulting in a large footprint and high energy consumption. As a promising alternative, chalcogenide phase-change materials (PCMs) exhibit strong modulation in a static, self-holding fashion. Here, we demonstrate nonvolatile electrically reconfigurable photonic switches using PCM-clad silicon waveguides and microring resonators that are intrinsically compact and energy-efficient. With phase transitions actuated by in-situ silicon PIN heaters, near-zero additional loss and reversible switching with high endurance are obtained in a complementary metal-oxide-semiconductor (CMOS)-compatible process. Our work can potentially enable very large-scale general-purpose programmable integrated photonic processors.

physics.app-ph↗

arXiv2019

Thermal conductivity of crystalline AlN and the influence of atomic-scale defects

Aluminum nitride (AlN) plays a key role in modern power electronics and deep-ultraviolet photonics, where an understanding of its thermal properties is essential. Here we measure the thermal conductivity of crystalline AlN by the 3$ω$ method, finding it ranges from 674 ${\pm}$ 56 W/m/K at 100 K to 186 ${\pm}$ 7 W/m/K at 400 K, with a value of 237 ${\pm}$ 6 W/m/K at room temperature. We compare these data with analytical models and first principles calculations, taking into account atomic-scale defects (O, Si, C impurities, and Al vacancies). We find Al vacancies play the greatest role in reducing thermal conductivity because of the largest mass-difference scattering. Modeling also reveals that 10% of heat conduction is contributed by phonons with long mean free paths, over ~7 $μ$m at room temperature, and 50% by phonons with MFPs over ~0.3 $μ$m. Consequently, the effective thermal conductivity of AlN is strongly reduced in sub-micron thin films or devices due to phonon-boundary scattering.

cond-mat.mtrl-sci↗

arXiv2019

Layer Dependent Interfacial Transport and Optoelectrical Properties of MoS2 on Ultra-flat Metals

Transition metal dichalcogenides (TMDs) are layered semiconducting van der Waal crystals and promising materials for a wide range of electronic and optoelectronic devices. Realizing practical electrical and optoelectronic device applications requires a connection between a metal junction and a TMD semiconductor. Hence, a complete understanding of electronic band alignments and the potential barrier heights governing the transport through a metal-TMD-metal junction is critical. But, there is a knowledge gap; it is not clear how the energy bands of a TMD align while in contact with a metal as a function of the number of layers. In pursuit of removing this knowledge gap, we have performed conductive atomic force microscopy (CAFM) of few layered (1-5) MoS2 immobilized on ultra-flat conducting Au surfaces (root mean square (RMS) surface roughness <0.2 nm) and indium tin oxide (ITO) substrate (RMS surface roughness <0.7 nm) forming a vertical metal (conductive-AFM tip)-semiconductor-metal device. We have observed that the current increases as the number of layers increases up to 5 layers. By applying Fowler-Nordheim tunneling theory, we have determined the barrier heights for different layers and observed that the barrier height decreases as the number of layers increases. Using density functional theory (DFT) calculation, we successfully demonstrated that the barrier height decreases as the layer number increases. By illuminating the TMDs on a transparent ultra-flat conducting ITO substrate, we observed a reduction in current when compared to the current measured in the dark, hence demonstrating negative photoconductivity. Our study provides a fundamental understanding of the local electronic and optoelectronic behaviors of TMD-metal junction, and may pave an avenue toward developing nanoscale electronic devices with tailored layer-dependent transport properties.

cond-mat.mes-hall↗

arXiv2019

Localized Triggering of the Insulator-Metal Transition in VO2 using a Single Carbon Nanotube

Vanadium dioxide (VO2) has been widely studied for its rich physics and potential applications, undergoing a prominent insulator-metal transition (IMT) near room temperature. The transition mechanism remains highly debated, and little is known about the IMT at nanoscale dimensions. To shed light on this problem, here we use ~1 nm wide carbon nanotube (CNT) heaters to trigger the IMT in VO2. Single metallic CNTs switch the adjacent VO2 at less than half the voltage and power required by control devices without a CNT, with switching power as low as ~85 $μW$ at 300 nm device lengths. We also obtain potential and temperature maps of devices during operation using Kelvin Probe Microscopy (KPM) and Scanning Thermal Microscopy (SThM). Comparing these with three-dimensional electrothermal simulations, we find that the local heating of the VO2 by the CNT play a key role in the IMT. These results demonstrate the ability to trigger IMT in VO2 using nanoscale heaters, and highlight the significance of thermal engineering to improve device behaviour.

cond-mat.mtrl-sci↗

arXiv2019

Contact Engineering High Performance n-Type MoTe2 Transistors

Semiconducting MoTe2 is one of the few two-dimensional (2D) materials with a moderate band gap, similar to silicon. However, this material remains under-explored for 2D electronics due to ambient instability and predominantly p-type Fermi level pinning at contacts. Here, we demonstrate unipolar n-type MoTe2 transistors with the highest performance to date, including high saturation current (>400 $μA/μm$ at 80 K and >200 $μA/μm$ at 300 K) and relatively low contact resistance (1.2 to 2 $kΩ\cdotμm$ from 80 to 300 K), achieved with Ag contacts and AlOx encapsulation. We also investigate other contact metals, extracting their Schottky barrier heights using an analytic subthreshold model. High-resolution X-ray photoelectron spectroscopy reveals that interfacial metal-Te compounds dominate the contact resistance. Among the metals studied, Sc has the lowest work function but is the most reactive, which we counter by inserting monolayer h-BN between MoTe2 and Sc. These metal-insulator-semiconductor (MIS) contacts partly de-pin the metal Fermi level and lead to the smallest Schottky barrier for electron injection. Overall, this work improves our understanding of n-type contacts to 2D materials, an important advance for low-power electronics.

physics.app-ph↗

arXiv2019

Significant Phonon Drag Enables High Power Factor in the AlGaN/GaN Two-Dimensional Electron Gas

In typical thermoelectric energy harvesters and sensors, the Seebeck effect is caused by diffusion of electrons or holes in a temperature gradient. However, the Seebeck effect can also have a phonon drag component, due to momentum exchange between charge carriers and lattice phonons, which is more difficult to quantify. Here, we present the first study of phonon drag in the AlGaN/GaN two-dimensional electron gas (2DEG). We find that phonon drag does not contribute significantly to the thermoelectric behavior of devices with ~100 nm GaN thickness, which suppress the phonon mean free path. However, when the thickness is increased to ~1.2 $μ$m, up to 32% (88%) of the Seebeck coefficient at 300 K (50 K) can be attributed to the drag component. In turn, the phonon drag enables state-of-the-art thermoelectric power factor in the thicker GaN film, up to ~40 mW m$^{-1}$ K$^{-2}$ at 50 K. By measuring the thermal conductivity of these AlGaN/GaN films, we show that the magnitude of the phonon drag can increase even when the thermal conductivity decreases. Decoupling of thermal conductivity and Seebeck coefficient could enable important advancements in thermoelectric power conversion with devices based on 2DEGs.

cond-mat.mtrl-sci↗

arXiv2019

Strongly Tunable Anisotropic Thermal Transport in MoS2 by Strain and Lithium Intercalation: First--Principles Calculations

The possibility of tuning the vibrational properties and the thermal conductivity of layered van der Waals materials either chemically or mechanically paves the way to significant advances in nanoscale heat management. Using first-principles calculations we investigate the modulation of heat transport in MoS2 by lithium intercalation and cross-plane strain. We find that both the in-plane and cross-plane thermal conductivity (kr, kz) of MoS2 are extremely sensitive to both strain and electrochemical intercalation. Combining lithium intercalation and strain, the in-plane and cross-plane thermal conductivity can be tuned over one and two orders of magnitude, respectively. Furthermore, since kr and kz respond in different ways to intercalation and strain, the thermal conductivity anisotropy can be modulated by two orders of magnitude. The underlying mechanisms for such large tunability of the anisotropic thermal conductivity of \Mos are explored by computing and analyzing the dispersion relations, group velocities, relaxation times and mean free paths of phonons. Since both intercalation and strain can be applied reversibly, their stark effect on thermal conductivity can be exploited to design novel phononic devices, as well as for thermal management in MoS2-based electronic and optoelectronic systems.

cond-mat.mtrl-sci↗

arXiv2019

Thermal Boundary Conductance of Two-Dimensional $MoS_{2}$ Interfaces

Understanding the thermal properties of two-dimensional (2D) materials and devices is essential for thermal management of 2D applications. Here we perform molecular dynamics simulations to evaluate both the specific heat of $MoS_{2}$ as well as the thermal boundary conductance (TBC) between one to five layers of $MoS_{2}$ with amorphous $SiO_{2}$ and between single-layer $MoS_{2}$ and crystalline $AlN$. The results of all calculations are compared to existing experimental data. In general, the TBC of such 2D interfaces is low, below ~20 $MWm^{-2}K^{-1}$, due to the weak van der Waals (vdW) coupling and mismatch of phonon density of states (PDOS) between materials. However, the TBC increases with vdW coupling strength, with temperature, and with the number of $MoS_{2}$ layers (which introduce additional phonon modes). These findings suggest that the TBC of 2D materials is tunable by modulating their interface interaction, the number of layers, and finding a PDOS-matched substrate, with important implications for future energy-efficient 2D electronics, photonics, and thermoelectrics.

cond-mat.mes-hall↗

arXiv2019

Quasi-ballistic thermal transport across MoS$_2$ thin films

Layered two-dimensional (2D) materials have highly anisotropic thermal properties between the in-plane and cross-plane directions. In general, it is thought that cross-plane thermal conductivities ($κ_z$) are low, and therefore c-axis phonon mean free paths (MFPs) are small. Here, we measure $κ_z$ across MoS$_2$ films of varying thickness (20 to 240 nm) and uncover evidence of very long c-axis phonon MFPs at room temperature in these layered semiconductors. Experimental data obtained using time-domain thermoreflectance (TDTR) are in good agreement with first-principles density functional theory (DFT). These calculations reveal that ~50% of the heat is carried by phonons with MFP >200 nm, exceeding kinetic theory estimates by nearly two orders of magnitude. Because of quasi-ballistic effects, the $κ_z$ of nanometer thin films of MoS$_2$ scales with their thickness and the volumetric thermal resistance asymptotes to a non-zero value, ~10 m$^{2}$KGW$^{-1}$. This contributes as much as 30% to the total thermal resistance of a 20 nm thick film, the rest being limited by thermal interface resistance with the SiO$_2$ substrate and top-side aluminum transducer. These findings are essential for understanding heat flow across nanometer-thin films of MoS$_2$ for optoelectronic and thermoelectric applications.

cond-mat.mes-hall↗

arXiv2019

Fast Spiking of a Mott VO2-Carbon Nanotube Composite Device

The recent surge of interest in brain-inspired computing and power-efficient electronics has dramatically bolstered development of computation and communication using neuron-like spiking signals. Devices that can produce rapid and energy-efficient spiking could significantly advance these applications. Here we demonstrate DC-current or voltage-driven periodic spiking with sub-20 ns pulse widths from a single device composed of a thin VO2 film with a metallic carbon nanotube as a nanoscale heater. Compared with VO2-only devices, adding the nanotube heater dramatically decreases the transient duration and pulse energy, and increases the spiking frequency, by up to three orders of magnitude. This is caused by heating and cooling of the VO2 across its insulator-metal transition being localized to a nanoscale conduction channel in an otherwise bulk medium. This result provides an important component of energy-efficient neuromorphic computing systems, and a lithography-free technique for power-scaling of electronic devices that operate via bulk mechanisms.

physics.app-ph↗

arXiv2019

Engineering Thermal and Electrical Interface Properties of Phase Change Memory with Monolayer MoS2

Phase change memory (PCM) is an emerging data storage technology, however its programming is thermal in nature and typically not energy-efficient. Here we reduce the switching power of PCM through the combined approaches of filamentary contacts and thermal confinement. The filamentary contact is formed through an oxidized TiN layer on the bottom electrode, and thermal confinement is achieved using a monolayer semiconductor interface, three-atom thick MoS2. The former reduces the switching volume of the phase change material and yields a 70% reduction in reset current versus typical 150 nm diameter mushroom cells. The enhanced thermal confinement achieved with the ultra-thin (~6 Å) MoS2 yields an additional 30% reduction in switching current and power. We also use detailed simulations to show that further tailoring the electrical and thermal interfaces of such PCM cells toward their fundamental limits could lead up to a six-fold benefit in power efficiency.

physics.app-ph↗

arXiv2019

An electrochemical thermal transistor

The ability to actively regulate heat flow at the nanoscale could be a game changer for applications in thermal management and energy harvesting. Such a breakthrough could also enable the control of heat flow using thermal circuits, in a manner analogous to electronic circuits. Here we demonstrate switchable thermal transistors with an order of magnitude thermal on/off ratio, based on reversible electrochemical lithium intercalation in MoS2 thin films. We use spatially-resolved time-domain thermoreflectance to map the lithium ion distribution during device operation, and atomic force microscopy to show that the lithiated state correlates with increased thickness and surface roughness. First principles calculations reveal that the thermal conductance modulation is due to phonon scattering by lithium rattler modes, c-axis strain, and stacking disorder. This study lays the foundation for electrochemically-driven nanoscale thermal regulators, and establishes thermal metrology as a useful probe of spatio-temporal intercalant dynamics in nanomaterials.

physics.app-ph↗