arXiv subjects

Fariborz Kargar

Publications and source records attributed to Fariborz Kargar.

At least 37 records · Page 2Linked to original sources

arXiv2023

Cryogenic Characteristics of Graphene Composites -- Evolution from Thermal Conductors to Thermal Insulators

The development of cryogenic semiconductor electronics and superconducting quantum computing requires composite materials that can provide both thermal conduction and thermal insulation. We demonstrated that at cryogenic temperatures, the thermal conductivity of graphene composites can be both higher and lower than that of the reference pristine epoxy, depending on the graphene filler loading and temperature. There exists a well-defined cross-over temperature - above it, the thermal conductivity of composites increases with the addition of graphene; below it, the thermal conductivity decreases with the addition of graphene. The counter-intuitive trend was explained by the specificity of heat conduction at low temperatures: graphene fillers can serve as, both, the scattering centers for phonons in the matrix material and as the conduits of heat. We offer a physical model that explains the experimental trends by the increasing effect of the thermal boundary resistance at cryogenic temperatures and the anomalous thermal percolation threshold, which becomes temperature dependent. The obtained results suggest the possibility of using graphene composites for, both, removing the heat and thermally insulating components at cryogenic temperatures - a capability important for quantum computing and cryogenically cooled conventional electronics.

cond-mat.mtrl-sci↗

arXiv2022

Specifics of the Elemental Excitations in "True One-Dimensional" MoI$_3$ van der Waals Nanowires

We report on the temperature evolution of the polarization-dependent Raman spectrum of exfoliated MoI$_3$, a van der Waals material with a "true one-dimensional" crystal structure that can be exfoliated to individual atomic chains. The temperature evolution of several Raman features reveals anomalous behavior suggesting a phase transition of a magnetic origin. Theoretical considerations indicate that MoI$_3$ is an easy-plane antiferromagnet with alternating spins along the dimerized chains and with inter-chain helical spin ordering. The calculated frequencies of the phonons and magnons are consistent with the interpretation of the experimental Raman data. The obtained results shed light on the specifics of the phononic and magnonic states in MoI$_3$ and provide a strong motivation for future study of this unique material with potential for spintronic device applications.

cond-mat.mes-hall↗

arXiv2022

Low-Frequency Noise in Quasi-1D (TaSe$_4$)$_2$I Weyl Semimetal Nanoribbons

We report on low-frequency current fluctuations, i.e. electronic noise, in quasi-one-dimensional (TaSe$_4$)$_2$I Weyl semimetal nanoribbons. It was found that the noise spectral density is of the 1/f type and scales with the square of the current, S~I^2 (f is the frequency). The noise spectral density increases by almost an order of magnitude and develops Lorentzian features near the temperature T~225 K. These spectral changes were attributed to the charge-density-wave phase transition even though the temperature of the noise maximum deviates from the reported Peierls transition temperature in bulk (TaSe$_4$)$_2$I crystals. The noise level, normalized by the channel area, in these Weyl semimetal nanoribbons was surprisingly low, $\sim 10^{-9}$ um$^2$Hz$^{-1}$ at f=10 Hz, when measured below and above the Peierls transition temperature. Obtained results shed light on the specifics of electron transport in quasi-1D topological Weyl semimetals and can be important for their proposed applications as downscaled interconnects.

cond-mat.mes-hall↗

arXiv2022

Electrical Gating of the Charge-Density-Wave Phases in Quasi-2D h-BN/1T-TaS$_2$ Devices

We report on electrical gating of the charge-density-wave phases and current in h-BN capped three-terminal 1T-TaS$_2$ heterostructure devices. It is demonstrated that the application of a gate bias can shift the source-drain current-voltage hysteresis associated with the transition between the nearly commensurate and incommensurate charge-density wave phases. The evolution of the hysteresis and the presence of abrupt spikes in the current while sweeping the gate voltage suggest that the effect is electrical rather than self-heating. We attribute the gating to an electric-field effect on the commensurate charge-density-wave domains in the atomic planes near the gate dielectric. The transition between the nearly commensurate and incommensurate charge-density-wave phases can be induced by both the source-drain current and the electrostatic gate. Since the charge-density-wave phases are persistent in 1T-TaS2 at room temperature, one can envision memory applications of such devices when scaled down to the dimensions of individual commensurate domains and few-atomic plane thicknesses.

physics.app-ph↗

arXiv2022

The Effects of Boron Doping on the Bulk and Surface Acoustic Phonons in Single-Crystal Diamond

We report the results of the investigation of bulk and surface acoustic phonons in the undoped and boron-doped single-crystal diamond films using the Brillouin-Mandelstam light scattering spectroscopy. The evolution of the optical phonons in the same set of samples was monitored with Raman spectroscopy. It was found that the frequency and the group velocity of acoustic phonons decrease non-monotonically with the increasing boron doping concentration, revealing pronounced phonon softening. The change in the velocity of the shear horizontal and the high-frequency pseudo-longitudinal acoustic phonons in the degenerately doped diamond, as compared to the undoped diamond, was as large as ~15% and ~12%, respectively. As a result of boron doping, the velocity of the bulk longitudinal and transverse acoustic phonons decreased correspondingly. The frequency of the optical phonons was unaffected at low boron concentration but experienced a strong decrease at the high doping level. The density-functional-theory calculations of the phonon band structure for the pristine and highly-doped sample confirm the phonon softening as a result of boron doping in diamond. The obtained results have important implications for thermal transport in heavily doped diamond, which is a promising material for ultra-wide-band-gap electronics.

cond-mat.mtrl-sci↗

arXiv2022

One-Dimensional van der Waals Quantum Materials -- State of the Art and Perspectives

The advent of graphene and other two-dimensional van der Waals materials, with their unique electrical, optical, and thermal properties, has resulted in tremendous progress for fundamental science. Recent developments suggest that taking one more step down in dimensionality - from monolayer, atomic sheets to individual atomic chains - can bring exciting prospects as the ultimate limit in material downscaling is reached while establishing an entirely new field of one-dimensional quantum materials. Here we review this emerging area of one-dimensional van der Waals quantum materials and anticipate its future directions. We focus on quantum effects associated with the charge-density-wave condensate, strongly-correlated phenomena, topological phases, and other unique physical characteristics, which are attainable specifically in van der Waals materials of lower dimensionality. Possibilities for engineering the properties of quasi-one-dimensional materials via compositional changes, vacancies, and defects, as well as the prospects of their applications in composites are also discussed.

cond-mat.mes-hall↗

arXiv2022

Charge-Density-Wave Devices Printed with the Ink of Chemically Exfoliated 1T-TaS$_2$ Fillers

We report on the preparation of inks containing fillers derived from quasi-two-dimensional charge-density-wave materials, their application for inkjet printing, and the evaluation of their electronic properties in printed thin film form. The inks were prepared by liquid-phase exfoliation of CVT-grown 1T-TaS$_2$ crystals to produce fillers with nm-scale thickness and um-scale lateral dimensions. Exfoliated 1T-TaS$_2$ was dispersed in a mixture of isopropyl alcohol and ethylene glycol to allow fine-tuning of their thermo-physical properties for inkjet printing. The temperature-dependent electrical and current fluctuation measurements of printed thin films demonstrated that the charge-density-wave properties of 1T-TaS$_2$ are preserved after processing. The functionality of the printed thin-film devices can be defined by the nearly-commensurate to commensurate charge-density-wave phase transition of individual exfoliated 1T-TaS$_2$ fillers rather than by electron-hopping transport between them. These results provide pathways for the development of printed electronics with diverse functionality achieved by the incorporation of quasi-two-dimensional van der Waals quantum materials.

cond-mat.mtrl-sci↗

arXiv2021

Excess Noise in High-Current Diamond Diodes -- Physical Mechanisms and Implications for Reliability Assessment

We report results of an investigation of low-frequency excess noise in high-current diamond diodes. It was found that the electronic excess noise of the diamond diodes is dominated by generation - recombination noise, which reveals itself either as Lorentzian spectral features or as a 1/f noise spectrum (f is the frequency). The generation - recombination bulges are characteristic for diamond diodes with lower turn-on voltages. The noise spectral density dependence on forward current, I, reveals three distinctive regions in all examined devices - it scales as I^2 at the low (I<10 uA) and high (I>10 mA) currents, and, rather unusually, remain nearly constant at the intermediate current range. The characteristic trap time constants, extracted from the noise data, reveal a uniquely strong dependence on current. Interestingly, the performance of the diamond diodes improves with increasing temperature. The obtained results are important for development of noise spectroscopy-based approaches for device reliability assessment for the high-power diamond electronics.

physics.app-ph↗

arXiv2021

Low-Frequency Noise Characteristics of GaN Vertical PIN Diodes -- Effects of Current and Temperature

We report low-frequency noise characteristics of vertical GaN PIN diodes, focusing on the effects of the diode design, current and temperature. The as-grown and regrown diodes, with and without surface treatment have been studied. The noise in most of the GaN devices had a characteristic 1/f spectrum at high and moderate currents, while some devices revealed generation-recombination bulges at low currents (f is the frequency). The predominant trend of the noise spectral density, S, dependence on the current was S ~ I. All tested GaN PIN diodes had rather low normalized noise spectral densities of 10^-18 cm2/Hz -- 10^-16 cm2/Hz (f=10 Hz) at the current density J=1 A/cm2 at room temperature. The noise temperature dependences at different currents revealed peaks at T=375 K -- 400 K. Temperature, current, and frequency dependences of noise suggest that the noise mechanism is of the recombination origin. We argue that the noise measurements at low currents can be used to efficiently assess the quality of GaN PIN diodes.

cond-mat.mtrl-sci↗

arXiv2021

Metallic vs. Semiconducting Properties of Quasi-One-Dimensional Tantalum Selenide van der Waals Nanoribbons

We conducted a tip-enhanced Raman scattering spectroscopy (TERS) and photoluminescence (PL) study of quasi-1D TaSe3 nanoribbons exfoliated onto gold substrates. At a selenium deficiency of ~0.25 (Se/Ta=2.75,), the nanoribbons exhibit a strong, broad PL peak centered around ~920 nm (1.35 eV), suggesting their semiconducting behavior. Such nanoribbons revealed a strong TERS response under 785-nm laser excitation, allowing for their nanoscale spectroscopic imaging. Nanoribbons with a smaller selenium deficiency of ~0.15 (Se/Ta=2.85) did not show any PL or TERS response. The confocal Raman spectra of these samples agree with the previously-reported spectra of metallic TaSe3. The differences in the optical response of the nanoribbons examined in this study suggest that even small variations in Se content can induce changes in electronic structure, causing samples to exhibit either metallic or semiconducting character. The temperature-dependent electrical measurements of devices fabricated with both types of materials corroborate these observations. The density-functional-theory calculations revealed that incorporation of an oxygen atom in a Se vacancy can result in band gap opening and thus enable the transition from a metal to a semiconductor. However, the predicted bandgap is substantially smaller than that derived from PL data. These results indicate that the properties of van der Waals materials can vary significantly depending on stoichiometry, defect types and concentration, and possibly environmental and substrate effects. In view of this finding, local probing of nanoribbon properties with TERS becomes essential to understanding such low-dimensional systems.

cond-mat.mtrl-sci↗

arXiv2021

Efficient Absorption of Terahertz Radiation in Graphene Polymer Composites

We demonstrate that polymer composites with a low loading of graphene, below 1.2 wt. %, are efficient as electromagnetic absorbers in the THz frequency range. The epoxy-based graphene composites were tested at frequencies from 0.25 THz to 4 THz, revealing total shielding effectiveness of 85 dB (1 mm thickness) with graphene loading of 1.2 wt. % at the frequency f=1.6 THz. The THz radiation is mostly blocked by absorption rather than reflection. The efficiency of the THz radiation shielding by the lightweight, electrically insulating composites, increases with increasing frequency. Our results suggest that even the thin-film or spray coatings of graphene composites with thickness in the few-hundred-micrometer range can be sufficient for blocking THz radiation in many practical applications.

physics.app-ph↗

arXiv2021

Thermal Transport in Graphene Composites: The Effect of Lateral Dimensions of Graphene Fillers

We report on the investigation of thermal transport in non-cured silicone composites with graphene fillers of different lateral dimensions. Graphene fillers are comprised of few-layer graphene flakes with lateral sizes in the range from 400 nm to 1200 nm and number of atomic planes from one to ~100. The distribution of the lateral dimensions and thicknesses of graphene fillers has been determined via atomic force microscopy statistics. It was found that in the examined range of the lateral dimensions the thermal conductivity of the composites increases with the increasing size of the graphene fillers. The observed difference in thermal properties can be related to the average gray phonon mean free path in graphene, which has been estimated to be around ~800 nm at room temperature. The thermal contact resistance of composites with graphene fillers of 1200-nm lateral dimensions was also smaller than that of composites with graphene fillers of 400-nm lateral dimensions. The effects of the filler loading fraction and the filler size on the thermal conductivity of the composites were rationalized within the Kanari model. The obtained results are important for optimization of graphene fillers for applications in thermal interface materials for heat removal from high-power-density electronics.

physics.app-ph↗

arXiv2021

Phonon modes and Raman signatures of MnBi2nTe3n+1 (n=1,2,3,4) magnetic topological heterostructures

An intrinsic antiferromagnetic topological insulator $\mathrm{MnBi_2Te_4}$ can be realized by intercalating Mn-Te bilayer chain in a topological insulator, $\mathrm{Bi_2Te_3}$. $\mathrm{MnBi_2Te_4}$ provides not only a stable platform to demonstrate exotic physical phenomena, but also easy tunability of the physical properties. For example, inserting more $\mathrm{Bi_2Te_3}$ layers in between two adjacent $\mathrm{MnBi_2Te_4}$ weakens the interlayer magnetic interactions between the $\mathrm{MnBi_2Te_4}$ layers. Here we present the first observations on the inter- and intra-layer phonon modes of $\mathrm{MnBi_{2n}Te_{3n+1}}$ (n=1,2,3,4) using cryogenic low-frequency Raman spectroscopy. We experimentally and theoretically distinguish the Raman vibrational modes using various polarization configurations. The two peaks at 66 cm$^{-1}$ and 112 cm$^{-1}$ show an abnormal perturbation in the Raman linewidths below the magnetic transition temperature due to spin-phonon coupling. In $\mathrm{MnBi_4Te_7}$, the $\mathrm{Bi_2Te_3}$ layers induce Davydov splitting of the A$_{1g}$ mode around 137 cm$^{-1}$ at 5 K. Using the linear chain model, we estimate the out-of-plane interlayer force constant to be $(3.98 \pm 0.14) \times 10^{19}$ N/m$^3$ at 5 K, three times weaker than that of $\mathrm{Bi_2Te_3}$. Our work discovers the dynamics of phonon modes of the $\mathrm{MnBi_2Te_4}$ and the effect of the additional $\mathrm{Bi_2Te_3}$ layers, providing the first-principles guidance to tailor the physical properties of layered heterostructures.

cond-mat.mtrl-sci↗

arXiv2021

Charge Transport in Electronic Devices Printed with Inks of Quasi-1D van der Waals Materials

We report on fabrication and characterization of electronic devices printed with inks of quasi-1D van der Waals materials. The quasi-1D van der Waals materials are characterized by 1D motifs in their crystal structure, which allows for their exfoliation into bundles of atomic chains. The ink was prepared by the liquid-phase exfoliation of crystals of TiS3 semiconductor into quasi-1D nanoribbons dispersed in a mixture of ethanol and ethylene glycol. The temperature dependent electrical measurements indicate that electron transport in the printed devices is dominated by the electron hopping mechanisms. The low-frequency electronic noise in the printed devices is of 1/f type near room temperature (f is the frequency). The abrupt changes in the temperature dependence of the noise spectral density and the spectrum itself can be indicative of the phase transition in individual TiS3 nanoribbons as well as modifications in the hopping transport regime. The obtained results attest to the potential of quasi-1D van der Waals materials for applications in printed electronics.

physics.app-ph↗

arXiv2021

Noncured Graphene Thermal Interface Materials: Minimizing the Thermal Contact Resistance

We report on experimental investigation of thermal contact resistance of the noncuring graphene thermal interface materials with the surfaces characterized by different degree of roughness. It is found that the thermal contact resistance depends on the graphene loading non-monotonically, achieving its minimum at the loading fraction of ~15 wt.%. Increasing the surface roughness by ~1 micrometer results in approximately the factor of x2 increase in the thermal contact resistance for this graphene loading. The obtained dependences of the thermal conductivity, thermal contact resistance, and the total thermal resistance of the thermal interface material layer on the graphene loading and surface roughness indicate the need for optimization of the loading fraction for specific materials and roughness of the connecting surfaces. Our results are important for developing graphene technologies for thermal management of high-power-density electronics.

physics.app-ph↗

arXiv2021

Low-Frequency Electronic Noise Spectroscopy of Quasi-2D van der Waals Antiferromagnetic Semiconductors

We investigated low-frequency current fluctuations, i.e. noise, in the quasi-two-dimensional (2D) van der Waals antiferromagnetic semiconductor FePS3 with the electronic bandgap of 1.5 eV. The electrical and noise characteristics of the p-type, highly resistive, thin films of FePS3 were measured at different temperatures. The noise spectral density was of the 1/f - type over most of the examined temperature range but revealed well-defined Lorentzian bulges, and increased strongly near the Neel temperature of 118 K (f is the frequency). Intriguingly, the noise spectral density attained its minimum at temperature T~200 K, which was attributed to an interplay of two opposite trends in noise scaling - one for semiconductors and another for materials with the phase transitions. The Lorentzian corner frequencies revealed unusual dependence on temperature and bias voltage, suggesting that their origin is different from the generation - recombination noise in conventional semiconductors. The obtained results are important for proposed applications of antiferromagnetic semiconductors in spintronic devices. They also attest to the power of the noise spectroscopy for monitoring various phase transitions.

cond-mat.mtrl-sci↗

arXiv2021

Electromagnetic-Polarization Selective Composites with Quasi-1D van der Waals Metallic Fillers

We report on the preparation of flexible polymer composite films with aligned metallic fillers comprised of atomic chain bundles of the quasi-one-dimensional (1D) van der Waals material tantalum triselenide, TaSe3. The material functionality, embedded at the nanoscale level, is achieved by mimicking the design of an electromagnetic aperture grid antenna. The processed composites employ chemically exfoliated TaSe3 nanowires as the grid building blocks incorporated within the thin film. Filler alignment is achieved using the "blade coating" method. Measurements conducted in the X-band frequency range demonstrate that the electromagnetic transmission through such films can be varied significantly by changing the relative orientations of the quasi-1D fillers and the polarization of the electromagnetic wave. We argue that such polarization-sensitive polymer films with quasi-1D fillers are applicable to advanced electromagnetic interference shielding in future communication systems.

cond-mat.mtrl-sci↗

arXiv2021

Electrically-Insulating Flexible Films with Quasi-One-Dimensional van-der-Waals Fillers as Efficient Electromagnetic Shields

We report polymer composite films containing fillers comprised of quasi-one-dimensional (1D) van der Waals materials, specifically transition metal trichalcogenides containing 1D structural motifs that enable their exfoliation into bundles of atomic threads. These nanostructures are characterized by extremely large aspect ratios of up to 10^6. The polymer composites with low loadings of quasi-1D TaSe3 fillers (below 3 vol. %) revealed excellent electromagnetic interference shielding in the X-band GHz and EHF sub-THz frequency ranges, while remaining DC electrically insulating. The unique electromagnetic shielding characteristics of these films are attributed to effective coupling of the electromagnetic waves to the high-aspect-ratio electrically-conductive TaSe3 atomic-thread bundles even when the filler concentration is below the electrical percolation threshold. These novel films are promising for high-frequency communication technologies, which require electromagnetic shielding films that are flexible, lightweight, corrosion resistant, electrically insulating and inexpensive.

cond-mat.mes-hall↗