Searcharxiv⌕ Search

arXiv subjects

Guanghua Gong

Publications and source records attributed to Guanghua Gong.

13 recordsLinked to original sources

Muon Detection and Direction Reconstruction with the Upgraded 1-ton Water Cherenkov Prototype Detector at CJPL-I

The 1-ton prototype detector for Jinping neutrino experiment (JNE-1ton) has completed its hardware upgrade and has been successfully operated in both water and liquid-scintillator modes at CJPL-I, which is situated under a 2400-m rock overburden. During the upgrade, the detector's mechanical support structure and PMT layout were redesigned. The original Hamamatsu PMTs were replaced with 8-inch MCP-PMTs from North Night Vision, increasing the PMT count from 30 to 60. The detector was then operated in water mode for 85 days (Water-I) and 79 days (Water-II). From the accumulated water-mode data, we derive a muon detection efficiency (Water-II) that is approximately 59% higher than that of the pre-upgrade liquid scintillator detector. The measured muon flux is $ϕ_{\text{I+II}} = (3.55 \pm 0.43_{\mathrm{stat}}\pm 0.28_{\mathrm{syst}}) \times 10^{-10}~\mathrm{cm}^{-2}\mathrm{s}^{-1}$, which is consistent with the previous measurement. Owing to the characteristic angular dependence of Cherenkov radiation and the increased PMT coverage, the uncertainty in muon direction reconstruction is approximately 6$^\circ$, which corresponds to a reduction to 30% of its previous value. Notably, one rare up-going muon event was clearly identified. It is excluded from the cosmic-ray muon flux sample and opens a new window for neutrino-induced event studies in the deepest underground laboratory in China. This work marks the first time that CJPL has employed a cost-effective water detector for muon flux measurement.

hep-ex↗

Investigating Production of TeV-scale Muons in Extensive Air Shower at 2400 Meters Underground

Deep underground experiments present a new avenue to probe the first interactions in extensive air showers or hadronic interactions in the extreme forward phase space. The China Jinping Underground Laboratory, characterized by a vertical rock overburden of 2,400~m, provides an exceptionally effective shield against cosmic muons with energies below 3~TeV. The surviving high-energy muons, produced in the first interactions of extensive air showers, open a unique observational window into primary cosmic rays from tens of TeV up to the PeV scale and beyond. This distinctive feature also enables detailed studies of charged hadron production in the earliest stages of shower development. Using 1,338.6 live days of data collected with a one-ton prototype detector for the Jinping Neutrino Experiment, we measured the underground muon flux originating from air showers. The results show discrepancies of about 40\% corresponding to significances of more than 2$σ$, relative to predictions from several leading hadronic interaction models. We interpret these findings from two complementary perspectives: (i) by adopting the expected cosmic-ray spectra, we constrain the modeling of the first hadronic interactions in air showers and provide novel insights into resolving the long-standing \textit{muon puzzle}; and (ii) by assuming specific hadronic interaction models, we infer the mass composition of cosmic rays, and our data favor a lighter component in the corresponding energy range. Our study demonstrates the potential of deep underground laboratories to provide new experimental insights into air shower physics and cosmic rays.

hep-ex↗

Ultrahigh-Energy Gamma-ray Emission Associated with Black Hole-Jet Systems

Black holes (BH), one of the most intriguing objects in the universe, can manifest themselves through electromagnetic radiation initiated by the accretion flow. Some stellar-mass BHs drive relativistic jets when accreting matter from their companion stars, forming microquasars. Non-thermal emission from the radio to tera-electronvolt (TeV) gamma-ray band has been observed from microquasars, indicating the acceleration of relativistic particles. Here we report detection of four microquasars (SS 433, V4641 Sgr, GRS 1915+105, MAXI J1820+070) of spectrum extending to the ultrahigh-energy (UHE; photon energy $E>100$ TeV) band and one microquasar (Cygnus X-1) of spectrum approaching 100 TeV, using the Large High Altitude Air Shower Observatory (LHAASO). Notably, the total emission associated with SS 433 cannot be interpreted with a single leptonic component. In the UHE band, its emission is in spatial coincidence with a giant atomic cloud, which is consistent with a hadronic origin. An elongated source is discovered from V4641 Sgr with the spectrum continuing up to 800 TeV. The detection of UHE gamma rays demonstrates that accreting BHs and their environments can operate as extremely efficient accelerators of particles out of 1 peta-electronvolt (PeV), suggesting microquasars to be important contributors to Galactic cosmic rays especially around the `knee' region.

astro-ph.HE↗

A Giant Peanut-shaped Ultra-High-Energy Gamma-Ray Emitter Off the Galactic Plane

Ultra-high-energy (UHE), exceeding 100 TeV (10^12 electronvolts), γ-rays manifests extreme particle acceleration in astrophysical sources. Recent observations by γ-ray telescopes, particularly by the Large High Altitude Air Shower Observatory (LHAASO), have revealed a few tens of UHE sources, indicating numerous Galactic sources capable of accelerating particles to PeV (10^15 electronvolts) energies. However, discerning the dominant acceleration mechanisms (leptonic versus hadronic), the relative contributions of specific source classes, and the role of particle transport in shaping their observed emission are central goals of modern UHE astrophysics. Here we report the discovery of a giant UHE γ-ray emitter at -17.5° off the Galactic plane - a region where UHE γ-ray sources are rarely found. The emitter exhibits a distinctive asymmetric shape, resembling a giant "Peanut" spanning 0.45° \times 4.6°, indicative of anisotropic particle distribution over a large area. A highly aged millisecond pulsar (MSP) J0218+4232 is the sole candidate accelerator positionally coincident with the Peanut region. Its association with UHE γ-rays extending to 0.7 PeV, if confirmed, would provide the first evidence of a millisecond pulsar powering PeV particles. Such a finding challenges prevailing models, which posit that millisecond pulsars cannot sustain acceleration to PeV energies. The detection reveals fundamental gaps in understanding particle acceleration, cosmic-ray transport, and interstellar magnetic field effects, potentially revealing new PeV accelerator (PeVatron) classes.

astro-ph.HE↗

JUNO 20-inch PMT and electronics system characterization using large pulses of PMT dark counts at the Pan-Asia testing platform

The main goal of the JUNO experiment is to determine the neutrino mass ordering with a 20kt liquid-scintillator detector. The 20-inch PMT and its 1F3 (one for three) electronics are crucial to realize the excellent energy resolution of at least 3% at 1MeV. The knowledge on the PMT and 1F3 electronics response is critical for detector performance understanding. A study of the JUNO 20-inch PMT and 1F3 electronics system characterization is presented using large pulses of PMT dark count at the Pan-Asia testing platform in China. Thanks to its broad amplitude range and high rate, the large pulse signals are also used to investigate the PMT after pulse response.

physics.ins-det↗

Implementation and performances of the IPbus protocol for the JUNO Large-PMT readout electronics

The Jiangmen Underground Neutrino Observatory (JUNO) is a large neutrino detector currently under construction in China. Thanks to the tight requirements on its optical and radio-purity properties, it will be able to perform leading measurements detecting terrestrial and astrophysical neutrinos in a wide energy range from tens of keV to hundreds of MeV. A key requirement for the success of the experiment is an unprecedented 3% energy resolution, guaranteed by its large active mass (20 kton) and the use of more than 20,000 20-inch photo-multiplier tubes (PMTs) acquired by high-speed, high-resolution sampling electronics located very close to the PMTs. As the Front-End and Read-Out electronics is expected to continuously run underwater for 30 years, a reliable readout acquisition system capable of handling the timestamped data stream coming from the Large-PMTs and permitting to simultaneously monitor and operate remotely the inaccessible electronics had to be developed. In this contribution, the firmware and hardware implementation of the IPbus based readout protocol will be presented, together with the performances measured on final modules during the mass production of the electronics.

physics.ins-det↗

Mass testing of the JUNO experiment 20-inch PMTs readout electronics

The Jiangmen Underground Neutrino Observatory (JUNO) is a multi-purpose, large size, liquid scintillator experiment under construction in China. JUNO will perform leading measurements detecting neutrinos from different sources (reactor, terrestrial and astrophysical neutrinos) covering a wide energy range (from 200 keV to several GeV). This paper focuses on the design and development of a test protocol for the 20-inch PMT underwater readout electronics, performed in parallel to the mass production line. In a time period of about ten months, a total number of 6950 electronic boards were tested with an acceptance yield of 99.1%.

physics.ins-det↗

Validation and integration tests of the JUNO 20-inch PMTs readout electronics

The Jiangmen Underground Neutrino Observatory (JUNO) is a large neutrino detector currently under construction in China. JUNO will be able to study the neutrino mass ordering and to perform leading measurements detecting terrestrial and astrophysical neutrinos in a wide energy range, spanning from 200 keV to several GeV. Given the ambitious physics goals of JUNO, the electronic system has to meet specific tight requirements, and a thorough characterization is required. The present paper describes the tests performed on the readout modules to measure their performances.

physics.ins-det↗

Check on the features of potted 20-inch PMTs with 1F3 electronics prototype at Pan-Asia

The Jiangmen underground neutrino observatory (JUNO) is a neutrino project with a 20-kton liquid scintillator detector located at 700-m underground. The large 20-inch PMTs are one of the crucial components of the JUNO experiment aiming to precision neutrino measurements with better than 3% energy resolution at 1 MeV. The excellent energy resolution and a large fiducial volume provide many exciting opportunities for addressing important topics in neutrino and astro-particle physics. With the container #D at JUNO Pan-Asia PMT testing and potting station, the features of waterproof potted 20-inch PMTs were measured with JUNO 1F3 electronics prototype in waveform and charge, which are valuable for better understanding on the performance of the waterproof potted PMTs and the JUNO 1F3 electronics. In this paper, basic features of JUNO 1F3 electronics prototype run at Pan-Asia will be introduced, followed by an analysis of the waterproof potted 20-inch PMTs and a comparison with the results from commercial electronics used by the container #A and #B.

physics.ins-det↗

Preliminary Design of Integrated Digitizer Base for Photomultiplier Tube

In many physical experiments and applications with photomultiplier tubes (PMTs), high-speed pulse digitalization is used extensively. The current pulse from a PMT has a rising time of several to a hundred nanoseconds. The current pulse shape can be used to obtain the pulse energy and discriminate between different particles. The conventional readout system with a PMT uses the discrete or integrated pulse-shaping circuits and analogue-to-digital converter boards which are based on the NIM or VME system to implement the data acquisition function. In many applications, such as security instruments, there are only several PMTs used in the whole system, or in some distributed applications, long-distance analogue cable with high-voltage power cable is not applicable due to the tremendous number of channels and enormous distributed space. In this paper, an integrated digitizer base is designed and interfaced with a Cs2LiYCl6 (CLYC) scintillator with a PMT. The CLYC scintillator has the ability to realize the pulse shape discrimination (PSD) between the neutron and gamma-rays. There is only one Gigabit of unscreened twisted-pair cable needed for over 700 Mbps TCP data throughput and more than 10 W power. The boards of high voltage supply, current sensitive preamplifier, 500 MSPS/12-Bit ADC (Analog-to-Digital Converter), readout module based on ZYNQ SoC (System on Chip), power over Ethernet, and user interface circuits are stacked with board-to-board connectors. The system can achieve 4.6% gamma-ray energy resolution at 662 keV with a 20-μs pulse integral and PSD figure-of-merit of ~3.0 for the whole energy of neutrons and gamma-rays. This integrated digitizer base can also be interfaced with other detectors with a PMT.

physics.ins-det↗

Letter of Intent: Jinping Neutrino Experiment

Jinping Neutrino Experiment (Jinping) is proposed to significantly improve measurements on solar neutrinos and geoneutrinos in China Jinping Laboratory - a lab with a number of unparalleled features, thickest overburden, lowest reactor neutrino background, etc., which identify it as the world-best low-energy neutrino laboratory. The proposed experiment will have target mass of 4 kilotons of liquid scintillator or water-based liquid scintillator, with a fiducial mass of 2 kilotons for neutrino-electron scattering events and 3 kilotons for inverse-beta interaction events. A number of initial sensitivities studies have been carried out, including on the transition phase for the solar neutrinos oscillation from the vacuum to the matter effect, the discovery of solar neutrinos from the carbon-nitrogen-oxygen (CNO) cycle, the resolution of the high and low metallicity hypotheses, and the unambiguous separation on U and Th cascade decays from the dominant crustal anti-electron neutrinos in China.

physics.ins-det↗

Neutrino Physics with JUNO

The Jiangmen Underground Neutrino Observatory (JUNO), a 20 kton multi-purpose underground liquid scintillator detector, was proposed with the determination of the neutrino mass hierarchy as a primary physics goal. It is also capable of observing neutrinos from terrestrial and extra-terrestrial sources, including supernova burst neutrinos, diffuse supernova neutrino background, geoneutrinos, atmospheric neutrinos, solar neutrinos, as well as exotic searches such as nucleon decays, dark matter, sterile neutrinos, etc. We present the physics motivations and the anticipated performance of the JUNO detector for various proposed measurements. By detecting reactor antineutrinos from two power plants at 53-km distance, JUNO will determine the neutrino mass hierarchy at a 3-4 sigma significance with six years of running. The measurement of antineutrino spectrum will also lead to the precise determination of three out of the six oscillation parameters to an accuracy of better than 1\%. Neutrino burst from a typical core-collapse supernova at 10 kpc would lead to ~5000 inverse-beta-decay events and ~2000 all-flavor neutrino-proton elastic scattering events in JUNO. Detection of DSNB would provide valuable information on the cosmic star-formation rate and the average core-collapsed neutrino energy spectrum. Geo-neutrinos can be detected in JUNO with a rate of ~400 events per year, significantly improving the statistics of existing geoneutrino samples. The JUNO detector is sensitive to several exotic searches, e.g. proton decay via the $p\to K^++\barν$ decay channel. The JUNO detector will provide a unique facility to address many outstanding crucial questions in particle and astrophysics. It holds the great potential for further advancing our quest to understanding the fundamental properties of neutrinos, one of the building blocks of our Universe.

physics.ins-det↗

Temperature Effect and Correction Method of White Rabbit Timing Link

To guarantee the angular resolution, the Large High Altitude Air Shower Observatory (LHAASO) requires a 500ps (rms) timing synchronization among the 6866 detect units for its KM2A sub-detector array. The White Rabbit technology is applied which combines sub-nanosecond precision timing transfer and gigabit Ethernet data transfer over the same fiber media. Deployed on a wild field at 4300m a.s.l. altitude, the WR network must maintain the precision over a wide temperature range. The temperature effect on a small WR link is measured, and contributions from different components like optical fiber, SFP module, fixed delay on PCB and ICs are separately studied and analyzed. An online real-time temperature correction method was applied based on the result which significantly reduce the synchronization variation from 300 ps to 50 ps in a temperature range of 50 degrees centigrade.

physics.ins-det↗