Searcharxiv⌕ Search

arXiv subjects

L. Zschiedrich

Publications and source records attributed to L. Zschiedrich.

At least 19 recordsLinked to original sources
arXiv2018

Quasinormal mode solvers for resonators with dispersive materials

Optical resonators are widely used in modern photonics. Their spectral response and temporal dynamics are fundamentally driven by their natural resonances, the so-called quasinormal modes (QNMs), with complex frequencies. For optical resonators made of dispersive materials, the QNM computation requires solving a nonlinear eigenvalue problem. This rises a difficulty that is only scarcely documented in the literature. We review our recent efforts for implementing efficient and accurate QNM-solvers for computing and normalizing the QNMs of micro- and nano-resonators made of highly-dispersive materials. We benchmark several methods for three geometries, a two-dimensional plasmonic crystal, a two-dimensional metal grating, and a three-dimensional nanopatch antenna on a metal substrate, in the perspective to elaborate standards for the computation of resonance modes.

physics.comp-ph↗
arXiv2017

Quantifying parameter uncertainties in optical scatterometry using Bayesian inversion

We present a Newton-like method to solve inverse problems and to quantify parameter uncertainties. We apply the method to parameter reconstruction in optical scatterometry, where we take into account a priori information and measurement uncertainties using a Bayesian approach. Further, we discuss the influence of numerical accuracy on the reconstruction result.

physics.comp-ph↗
arXiv2016

hp-finite-elements for simulating electromagnetic fields in optical devices with rough textures

The finite-element method is a preferred numerical method when electromagnetic fields at high accuracy are to be computed in nano-optics design. Here, we demonstrate a finite-element method using hp-adaptivity on tetrahedral meshes for computation of electromagnetic fields in a device with rough textures. The method allows for efficient computations on meshes with strong variations in element sizes. This enables to use precise geometry resolution of the rough textures. Convergence to highly accurate results is observed.

physics.optics↗
arXiv2015

hp-finite element method for simulating light scattering from complex 3D structures

Methods for solving Maxwell's equations are integral part of optical metrology and computational lithography setups. Applications require accurate geometrical resolution, high numerical accuracy and/or low computation times. We present a finite-element based electromagnetic field solver relying on unstructured 3D meshes and adaptive hp-refinement. We apply the method for simulating light scattering off arrays of high aspect-ratio nano-posts and FinFETs.

physics.optics↗
arXiv2013

Numerical analysis of nanostructures for enhanced light extraction from OLEDs

Nanostructures, like periodic arrays of scatters or low-index gratings, are used to improve the light outcoupling from organic light-emitting diodes (OLED). In order to optimize geometrical and material properties of such structures, simulations of the outcoupling process are very helpful. The finite element method is best suited for an accurate discretization of the geometry and the singular-like field profile within the structured layer and the emitting layer. However, a finite element simulation of the overall OLED stack is often beyond available computer resources. The main focus of this paper is the simulation of a single dipole source embedded into a twofold infinitely periodic OLED structure. To overcome the numerical burden we apply the Floquet transform, so that the computational domain reduces to the unit cell. The relevant outcoupling data are then gained by inverse Flouqet transforming. This step requires a careful numerical treatment as reported in this paper.

physics.optics↗
arXiv2013

Fast simulation method for parameter reconstruction in optical metrology

A method for automatic computation of parameter derivatives of numerically computed light scattering signals is demonstrated. The finite-element based method is validated in a numerical convergence study, and it is applied to investigate the sensitivity of a scatterometric setup with respect to geometrical parameters of the scattering target. The method can significantly improve numerical performance of design optimization, parameter reconstruction, sensitivity analysis, and other applications.

physics.optics↗
arXiv2012

3D finite element simulation of optical modes in VCSELs

We present a finite element method (FEM) solver for computation of optical resonance modes in VCSELs. We perform a convergence study and demonstrate that high accuracies for 3D setups can be attained on standard computers. We also demonstrate simulations of thermo-optical effects in VCSELs.

physics.optics↗
arXiv2011

Rigorous Simulations of 3D Patterns on Extreme Ultraviolet Lithography Masks

Simulations of light scattering off an extreme ultraviolet lithography mask with a 2D-periodic absorber pattern are presented. In a detailed convergence study it is shown that accurate results can be attained for relatively large 3D computational domains and in the presence of sidewall-angles and corner-roundings.

physics.optics↗
arXiv2010

Reduced basis method for source mask optimization

Image modeling and simulation are critical to extending the limits of leading edge lithography technologies used for IC making. Simultaneous source mask optimization (SMO) has become an important objective in the field of computational lithography. SMO is considered essential to extending immersion lithography beyond the 45nm node. However, SMO is computationally extremely challenging and time-consuming. The key challenges are due to run time vs. accuracy tradeoffs of the imaging models used for the computational lithography. We present a new technique to be incorporated in the SMO flow. This new approach is based on the reduced basis method (RBM) applied to the simulation of light transmission through the lithography masks. It provides a rigorous approximation to the exact lithographical problem, based on fully vectorial Maxwell's equations. Using the reduced basis method, the optimization process is divided into an offline and an online steps. In the offline step, a RBM model with variable geometrical parameters is built self-adaptively and using a Finite Element (FEM) based solver. In the online step, the RBM model can be solved very fast for arbitrary illumination and geometrical parameters, such as dimensions of OPC features, line widths, etc. This approach dramatically reduces computational costs of the optimization procedure while providing accuracy superior to the approaches involving simplified mask models. RBM furthermore provides rigorous error estimators, which assure the quality and reliability of the reduced basis solutions. We apply the reduced basis method to a 3D SMO example. We quantify performance, computational costs and accuracy of our method.

physics.optics↗
arXiv2010

Reduced basis method for computational lithography

A bottleneck for computational lithography and optical metrology are long computational times for near field simulations. For design, optimization, and inverse scatterometry usually the same basic layout has to be simulated multiple times for different values of geometrical parameters. The reduced basis method allows to split up the solution process of a parameterized model into an expensive offline and a cheap online part. After constructing the reduced basis offline, the reduced model can be solved online very fast in the order of seconds or below. Error estimators assure the reliability of the reduced basis solution and are used for self adaptive construction of the reduced system. We explain the idea of reduced basis and use the finite element solver JCMsuite constructing the reduced basis system. We present a 3D optimization application from optical proximity correction (OPC).

physics.optics↗
arXiv2010

Finite element method for accurate 3D simulation of plasmonic waveguides

Optical properties of hybrid plasmonic waveguides and of low-Q cavities, formed by waveguides of finite length are investigated numerically. These structures are of interest as building-blocks of plasmon lasers. We use a time-harmonic finite-element package including a propagation-mode solver, a resonance-mode solver and a scattering solver for studying various properties of the system. Numerical convergence of all used methods is demonstrated.

physics.optics↗
arXiv2010

Numerical Investigation of Photonic Crystal Microcavities in Silicon-on-Insulator Waveguides

Optical resonances in 1D photonic crystal microcavities are investigated numerically using finite-element light scattering and eigenmode solvers. The results are validated by comparison to experimental and theoretical findings from the literature. The influence of nanometer-scale geometry variations on the resonator performance is studied. Limiting factors to ultra-high Q-factor performance are identified.

physics.optics↗
arXiv2009

Accurate simulation of light transmission through subwavelength apertures in metal films

We use the finite-element method for simulating light transmission through a 2D-periodic array of rectangular apertures in a film of highly conductive material. We report results with a relative error of the transmissivity lower than 0.01%. This is an improvement of about one order of magnitude compared to previously reported results. Further, the influence of corner and edge roundings on light transmission through the subwavelength apertures is investigated.

physics.optics↗