arXiv subjects

Michele Buscema

Publications and source records attributed to Michele Buscema.

15 recordsLinked to original sources

arXiv2025

Imaging current flow and injection in scalable graphene devices through NV-magnetometry

The global electronic properties of solid-state devices are strongly affected by the microscopic spatial paths of charge carriers. Visualising these paths in novel devices produced by scalable processes would provide a quality assessment method that can propel the device performance metrics towards commercial use. Here, we use high-resolution nitrogen-vacancy (NV) magnetometry to visualise the charge flow in gold-contacted, single-layer graphene devices produced by scalable methods. Modulating the majority carrier type via field effect reveals a strong asymmetry between the spatial current distributions in the electron and hole regimes that we attribute to an inhomogeneous microscopic potential landscape, inaccessible to conventional measurement techniques. In addition, we observe large, unexpected, differences in charge flow through nominally identical gold-graphene contacts. Moreover, we find that the current transfer into the graphene occurs several microns before the metal contact edge. Our findings establish high-resolution NV-magnetometry as a key tool for characterizing scalable 2D material based devices, uncovering quality deficits of the material, substrate, and electrical contacts that are invisible to conventional methods.

cond-mat.mes-hall↗

arXiv2015

Gate-tunable diode and photovoltaic effect in an organic-2D layered material p-n junction

The semiconducting p-n junction is a simple device structure with great relevance for electronic and optoelectronic applications. The successful integration of low-dimensional materials in electronic circuits has opened the way forward for producing gate-tunable p-n junctions. In that context, here we present an organic (Cu-phthalocyanine)-2D layered material (MoS2) hybrid p-n junction with both gate-tunable diode characteristics and photovoltaic effect. Our proof-of-principle devices show multifunctional properties with diode rectifying factors of up to 10^4, while under light exposure they exhibit photoresponse with a measured external quantum efficiency of ~ 11 %. As for their photovoltaic properties, we found open circuit voltages of up to 0.6 V and optical-to-electrical power conversion efficiency of 0.7 %. The extended catalogue of known organic semiconductors and two-dimensional materials offer the prospect for tailoring the properties and the performance of the resulting devices, making organic-2D p-n junctions promising candidates for future technological applications.

cond-mat.mtrl-sci↗

arXiv2015

Gate controlled photocurrent generation mechanisms in high-gain In2Se3 phototransistors

Photocurrent in photodetectors incorporating van der Waals materials is typically produced by a combination of photocurrent generation mechanisms that occur simultaneously during operation. Because of this, response times in these devices often yield to slower, high gain processes which cannot be turned off. Here we report on photodetectors incorporating the layered material In2Se3, which allow complete modulation of a high gain, photogating mechanism in the ON state in favor of fast photoconduction in the OFF state. While photoconduction is largely gate independent, photocurrent from the photogating effect is strongly modulated through application of a back gate voltage. By varying the back gate, we demonstrate control over the dominant mechanism responsible for photocurrent generation. Furthermore, due to the strong photogating effect, these direct-band gap, multi-layer phototransistors produce ultra-high gains of (9.8 +- 2.5) x 10^4 A/W and inferred detectivities of (3.3 +- 0.8) x 10^13 Jones, putting In2Se3 amongst the most sensitive 2D materials for photodetection studied to date.

cond-mat.mes-hall↗

arXiv2015

Photocurrent generation with two-dimensional van der Waals semiconductors

Two-dimensional (2D) materials have attracted a great deal of interest in recent years. This family of materials allows for the realization of versatile electronic devices and holds promise for next-generation (opto)electronics. Their electronic properties strongly depend on the number of layers, making them interesting from a fundamental standpoint. For electronic applications, semiconducting 2D materials benefit from sizable mobilities and large on/off ratios, due to the large modulation achievable via the gate field-effect. Moreover, being mechanically strong and flexible, these materials can withstand large strain (>10\%) before rupture, making them interesting for strain engineering and flexible devices. Even in their single layer form, semiconducting 2D materials have demonstrated efficient light absorption, enabling large responsivity in photodetectors. Therefore, semiconducting layered 2D materials are strong candidates for optoelectronic applications, especially for photodetection. Here, we review the state-of-the-art in photodetectors based on semiconducting 2D materials, focusing on the transition metal dichalcogenides, novel van der Waals materials, black phosphorus, and heterostructures.

cond-mat.mes-hall↗

arXiv2014

Photovoltaic and photothermoelectric effect in a double-gated WSe2 device

Tungsten diselenide (WSe2), a semiconducting transition metal dichalcogenide (TMDC), shows great potential as active material in optoelectronic devices due to its ambipolarity and direct bandgap in its single-layer form. Recently, different groups have exploited the ambipolarity of WSe2 to realize electrically tunable PN junctions, demonstrating its potential for digital electronics and solar cell applications. In this Letter, we focus on the different photocurrent generation mechanisms in a double-gated WSe2 device by measuring the photocurrent (and photovoltage) as the local gate voltages are varied independently in combination with above- and below-bandgap illumination. This enables us to distinguish between two main photocurrent generation mechanisms: the photovoltaic and photothermoelectric effect. We find that the dominant mechanism depends on the defined gate configuration. In the PN and NP configurations, photocurrent is mainly generated by the photovoltaic effect and the device displays a maximum responsivity of 0.70 mA/W at 532 nm illumination and rise and fall times close to 10 ms. Photocurrent generated by the photothermoelectric effect emerges in the PP configuration and is a factor of two larger than the current generated by the photovoltaic effect (in PN and NP configurations). This demonstrates that the photothermoelectric effect can play a significant role in devices based on WSe2 where a region of strong optical absorption, caused by e.g. an asymmetry in flake thickness or optical absorption of the electrodes, generates a sizeable thermal gradient upon illumination.

cond-mat.mes-hall↗

arXiv2014

Photovoltaic effect in few-layer black phosphorus PN junctions defined by local electrostatic gating

The photovoltaic effect is one of the fundamental light-matter interactions in light energy harvesting. In conventional photovoltaic solar cells, the photogenerated charge carriers are extracted by the built-in electric field of a PN junction, typically defined by ionic dopants in a semiconductor. In atomically thin semiconductors, the doping level can be controlled by the field-effect without need of implanting dopants in the lattice, which makes 2D semiconductors prospective materials to implement electrically tunable PN junctions. However, most 2D semiconducting materials do not show ambipolar P-type and N-type field-effect transport, necessary to realize PN junctions. Few-layer black phosphorus is a recently isolated 2D semiconductor that presents a direct bandgap, high mobility, current on/off ratio and ambipolar operation. Here, we fabricate few-layer black phosphorus (b-P) field-effect transistors with split bottom gates and crystalline hexagonal boron nitride (h-BN) dielectric. We demonstrate electrostatic control of the local charge carrier type and density above each gate in the device, tuning its electrical behaviour from metallic to rectifying. Illuminating a gate-defined PN junction, we observe zero-bias photocurrents and significant open-circuit voltage, which we attribute to the separation of electron-hole pairs driven by the internal electric field at the junction region. Due to the small bandgap of the material, we observe photocurrents and photovoltages for illumination wavelengths up to 940 nm, attractive for energy harvesting applications in the near-infrared region

cond-mat.mes-hall↗

arXiv2014

Isolation and characterization of few-layer black phosphorus

Isolation and characterization of mechanically exfoliated black phosphorus flakes with a thickness down to two single-layers is presented. A modification of the mechanical exfoliation method, which provides higher yield of atomically thin flakes than conventional mechanical exfoliation, has been developed. We present general guidelines to determine the number of layers using optical microscopy, Raman spectroscopy and transmission electron microscopy in a fast and reliable way. Moreover, we demonstrate that the exfoliated flakes are highly crystalline and that they are stable even in free-standing form through Raman spectroscopy and transmission electron microscopy measurements. A strong thickness dependence of the band structure is found by density functional theory calculations. The exciton binding energy, within an effective mass approximation, is also calculated for different number of layers. Our computational results for the optical gap are consistent with preliminary photoluminescence results on thin flakes. Finally, we study the environmental stability of black phosphorus flakes finding that the flakes are very hydrophilic and that long term exposure to air moisture etches black phosphorus away. Nonetheless, we demonstrate that the aging of the flakes is slow enough to allow fabrication of field-effect transistors with strong ambipolar behavior. Density functional theory calculations also give us insight into the water-induced changes of the structural and electronic properties of black phosphorus.

cond-mat.mes-hall↗

arXiv2014

Ultrahigh photoresponse of few-layer TiS3 nanoribbon transistors

Here, we isolate thin TiS3 ribbons, a layered direct band gap semiconductor (1.1 eV, well suited for detection all across the visible spectrum), thus far almost unexplored. We fabricate field effect transistors and study their electrical characteristics and optoelectronic properties. The measured FET characteristics show mobilities up to 2.6 cm^2/Vs and ON/OFF ratios up to 10^4. Under illumination, the TiS3 NR-FETs present an ultrahigh photoresponse of 2910 A/W and fast rise/fall times of ~4 ms. In addition, we measure cutoff frequencies (f3dB) up to 1000 Hz. The strong combination of ultrahigh sensitivity all along the visible spectrum and fast time response of TiS3 nanoribbon transistors put them among the best nanoscale photodetectors to date.

cond-mat.mes-hall↗

arXiv2014

Fast and broadband photoresponse of few-layer black phosphorus field-effect transistors

Few-layer black phosphorus, a new elemental 2D material recently isolated by mechanical exfoliation, is a high-mobility layered semiconductor with a direct bandgap that is predicted to strongly depend on the number of layers, from 0.35 eV (bulk) to 2.0 eV (single-layer). Therefore, black phosphorus is an appealing candidate for tunable photodetection from the visible to the infrared part of the spectrum. We study the photoresponse of field-effect transistors (FETs) made of few-layer black phosphorus (3 nm to 8 nm thick), as a function of excitation wavelength, power and frequency. In the dark state, the black phosphorus FETs can be tuned both in hole and electron doping regimes allowing for ambipolar operation. We measure mobilities in the order of 100 cm2/V s and current ON/OFF ratio larger than 103. Upon illumination, the black phosphorus transistors show response to excitation wavelengths from the visible up to 940 nm and rise time of about 1 ms, demonstrating broadband and fast detection. The responsivity reaches 4.8 mA/W and it could be drastically enhanced by engineering a detector based on a PN junction. The ambipolar behavior coupled to the fast and broadband photodetection make few-layer black phosphorus a promising 2D material for photodetection across the visible and near-infrared part of the electromagnetic spectrum.

cond-mat.mes-hall↗

arXiv2014

Deterministic transfer of two-dimensional materials by all-dry viscoelastic stamping

Deterministic transfer of two-dimensional crystals constitutes a crucial step towards the fabrication of heterostructures based on artificial stacking of two-dimensional materials. Moreover, control on the positioning of two-dimensional crystals facilitates their integration in complex devices, which enables the exploration of novel applications and the discovery of new phenomena in these materials. Up to date, deterministic transfer methods rely on the use of sacrificial polymer layers and wet chemistry to some extent. Here, we develop an all-dry transfer method that relies on viscoelastic stamps and does not employ any wet chemistry step. This is found very advantageous to freely suspend these materials as there are no capillary forces involved in the process. Moreover, the whole fabrication process is quick, efficient, clean, and it can be performed with high yield.

cond-mat.mes-hall↗

arXiv2014

Single-layer MoS2 mechanical resonators

Here, we demonstrate the fabrication of single-layer MoS2 mechanical resonators. The fabricated resonators have fundamental resonance frequencies in the order of 10 MHz to 30 MHz (depending on their geometry) and their quality factor is about ~55 at room temperature in vacuum. The dynamical properties clearly indicate that monolayer MoS2 membranes are in the membrane limit (i.e., tension dominated), in contrast to their thicker counterparts, which behave as plates. We also demonstrate clear signatures of nonlinear behaviour of our atomically thin membranes, thus providing a starting point for future investigations on the nonlinear dynamics of monolayer nanomechanical resonators.

cond-mat.mes-hall↗

arXiv2013

Local strain engineering in atomically thin MoS2

Tuning the electronic properties of a material by subjecting it to strain constitutes an important strategy to enhance the performance of semiconducting electronic devices. Using local strain, confinement potentials for excitons can be engineered, with exciting possibilities for trapping excitons for quantum optics and for efficient collection of solar energy. Two-dimensional materials are able to withstand large strains before rupture, offering a unique opportunity to introduce large local strains. Here, we study atomically thin MoS2 layers with large local strains of up to 2.5% induced by controlled delamination from a substrate. Using simultaneous scanning Raman and photoluminescence imaging, we spatially resolve a direct bandgap reduction of up to 90 meV induced by local strain. We observe a funnel effect in which excitons drift hundreds of nanometers to lower bandgap regions before recombining, demonstrating exciton confinement by local strain. The observations are supported by an atomistic tight-binding model developed to predict the effect of inhomogeneous strain on the local electronic states in MoS2. The possibility of generating large strain-induced variations in exciton trapping potentials opens the door for a variety of applications in atomically thin materials including photovoltaics, quantum optics and two-dimensional optoelectronic devices.

cond-mat.mes-hall↗

arXiv2013

The effect of the substrate on the Raman and photoluminescence emission of single layer MoS2

We quantitatively study the Raman and photoluminescence (PL) emission from single layer molybdenum disulfide (MoS2) on dielectric (SiO2, hexagonal boron nitride, mica and the polymeric dielectric Gel-Film) and conducting substrates (Au and few-layer graphene). We find that the substrate can affect the Raman and PL emission in a twofold manner. First, the absorption and emission intensities are strongly modulated by the constructive/destructive interference within the different substrates. Second, the position of the A1g Raman mode peak and the spectral weight between neutral and charged excitons in the PL spectra are modified by the substrate. We attribute this effect to substrate-induced changes in the doping level and in the decay rates of the excitonic transitions. Our results provide a method to quantitatively study the Raman and PL emission from MoS2-based vertical heterostructures and represent the first step in ad-hoc tuning the PL emission of 1L MoS2 by selecting the proper substrate.

cond-mat.mtrl-sci↗

arXiv2013

Large and tunable photo-thermoelectric effect in single-layer MoS2

We study the photoresponse of single-layer MoS2 field-effect transistors by scanning photocurrent microscopy. We find that, unlike in many other semiconductors, the photocurrent generation in single-layer MoS2 is dominated by the photo-thermoelectric effect and not by the separation of photoexcited electron-hole pairs across the Schottky barriers at the MoS2/electrode interfaces. We observe a large value for the Seebeck coefficient for single-layer MoS2 that, by an external electric field, can be tuned between -4x10^2 uV/K and -1x10^5 uV/K. This large and tunable Seebeck coefficient of the single-layer MoS2 paves the way to new applications of this material such as on-chip thermopower generation and waste thermal energy harvesting.

cond-mat.mes-hall↗

arXiv2012

Fast and efficient photodetection in nanoscale quantum-dot junctions

We report on a photodetector in which colloidal quantum-dots directly bridge nanometer-spaced electrodes. Unlike in conventional quantum-dot thin film photodetectors, charge mobility no longer plays a role in our quantum-dot junctions as charge extraction requires only two individual tunnel events. We find an efficient photoconductive gain mechanism with external quantum-efficiencies of 38 electrons-per-photon in combination with response times faster than 300 ns. This compact device-architecture may open up new routes for improved photodetector performance in which efficiency and bandwidth do not go at the cost of one another.

cond-mat.mes-hall↗