arXiv subjects

Siddharth Rajan

Publications and source records attributed to Siddharth Rajan.

At least 19 recordsLinked to original sources

arXiv2026

Vertical Gallium Oxide Isolated Source Electrode Field Effect Transistors (ISEFET) Without Planarization or Mid-Gap Acceptor Blocking Layers

We propose and demonstrate the first vertical Gallium oxide device architecture without the use of planarization etch back processes or mid-gap acceptor regions. The Isolated Source Electrode Field Effect Transistor (ISEFET) incorporates a dielectric blocking layer to access an isolated source pad extending from the top fin metal. Scaled multi-fin channels were formed by electron beam lithography with a width of 200 nm along with the source pads and then etched to a trench depth of ~1.2 um. The fabricated devices showed enhancement mode operation with threshold voltage of 2 V and on-off ratio > 1e7 with excellent gate modulation characteristics. The resulting device proved to be comparable to existing vertical transistors and suitable for high-throughput prototyping and large-scale manufacturing of future Gallium oxide and other wide bandgap semiconductor devices.

physics.app-ph↗

arXiv2026

AlN Gate Interlayer for UWBG AlGaN Transistors with Breakdown Field >6.9 MV/cm and PFOM >1.8 GW/cm2

We report the demonstration of regrown epitaxial AlN gate interlayers with ultra-wide bandgap (UWBG) AlGaN polarization-graded field effect transistors (PolFETs). The introduction of the epitaxial AlN gate interlayer enables significant improvement in breakdown strength, with average breakdown field exceeding 6.94 MV/cm, which represents state-of-the-art for lateral field effect transistors, while maintaining excellent on-state current density exceeding 1 A/mm. The integration of epitaxial AlN enables state-of-the-art power-switching figure of merit exceeding 1.87 GW/cm2 at a breakdown voltage exceeding 1.45 kV. This work shows the potential of UWBG AlGaN for next-generation high-power switching and RF applications with enhanced device performance established by a high-quality epitaxially regrown AlN gate interlayer.

physics.app-ph↗

arXiv2026

High Breakdown Field Multi-kV UWBG AlGaN Transistors

We demonstrate high-performance UWBG AlGaN PolFETs exhibiting a state-of-the-art combination of nearly 1 A/mm on-state current (~ 960 mA/mm) and large breakdown field (> 4.8 MV/cm) in high carrier density (1.15 x 1013 cm-2). Multi-kV robustness is successfully demonstrated exhibiting 1.28 and 2.17 kV by utilizing a gate-connected field plate structures in 3.9 and 6.8 {\mu}m LGD, corresponding to the extremely low specific on-resistance of 1.25 and 2.86 m{\Omega}cm2, respectively. High RF performance is also achieved, providing fT and fMAX, of 8.5 and 15 GHz, respectively, for 3.9 {\mu}m LGD. These results highlight UWBG AlGaN as a platform for both high-voltage RF and power applications.

physics.app-ph↗

arXiv2026

Electrostatic Effects of Self Trapped Holes in Gallium Oxide Devices

Gallium oxide is an ultra-wide bandgap semiconductor with exceptional properties for power electronics and UV-C optoelectronics, but its behavior under illumination remains poorly understood. In this work, we investigate how optically generated self-trapped holes influence electrostatics and current conduction in gallium oxide devices. Using a vertical Schottky photodiode with a semi-transparent Ni anode, we performed capacitance-voltage, current-voltage, and temperature-dependent I-V measurements under dark and above-bandgap illumination. Analysis of photocurrent gain reveals that conventional image-force barrier-lowering models require unrealistically high interfacial electric fields, suggesting the presence of an alternative mechanism. By applying Fowler-Nordheim tunneling theory, we reconcile measured photocurrents and photo-capacitance results with physically plausible fields and quantify the two-dimensional concentration of self-trapped holes. Our findings demonstrate that illumination-induced charge significantly alters device electrostatics. Understanding this tunneling-based photocurrent gain mechanism is critical for designing gallium oxide devices for UV-C detectors and power electronics.

cond-mat.mtrl-sci↗

arXiv2026

Extremely Low Thermal Resistance Architectures for AlxGaN1-x Semiconductor Devices

Next-generation high-power radio-frequency (RF) devices increasingly demand transistors that operate efficiently with high gain at high frequencies. High-aluminum-content ultra-wide-bandgap (UWBG) AlGaN alloys have shown great potential for enabling such high-frequency RF technologies. However, the widespread adoption of AlGaN-based RF devices is limited by thermal-management challenges arising from the intrinsically low thermal conductivity of AlGaN, which leads to higher device thermal resistance for a given geometry compared to GaN RF devices. As a result, these next-generation devices are highly susceptible to self-heating. This study investigates the thermal behavior of UWBG AlGaN devices, focusing on the effects of AlGaN channel thickness, substrate technology, and high-k material integration on reducing device thermal resistance to enable high-power operation. Experimental results demonstrate a record-low thermal resistance of 3.96 mm$\cdot$K/W when an AlN substrate is employed and the AlGaN channel thickness is reduced to 5 nm. These findings provide valuable insights into mitigating thermal limitations in UWBG devices through device-level engineering and the strategic integration of high-k materials.

physics.app-ph↗

arXiv2025

Ultra-Wide Bandgap AlGaN Heterostructure Field Effect Transistors with Current Gain Cutoff Frequency Above 85 GHz

We report the design and demonstration of ultra-wide-bandgap (UWBG) AlGaN polarization-graded field-effect transistors (PolFETs) that achieve a current-gain cutoff frequency above 85 GHz and a current density exceeding 1.3 A/mm. Ultra-thin channel and buffer layers were grown epitaxially on AlN substrates, and a reverse-graded AlGaN contact layer was incorporated to reduce the contact resistance to below 1 ohm.mm. With aggressively scaled device dimensions, the AlGaN PolFETs exhibit state-of-the-art high-frequency performance for UWBG transistors. Small-signal modeling reveals both parasitic and transit delays, confirming the benefits of reduced access resistance and enhanced intrinsic transconductance. These results establish a new performance benchmark for UWBG AlGaN devices and demonstrate their strong potential for next-generation millimeter-wave electronics.

physics.app-ph↗

arXiv2025

Scaled Ultra-Wide Bandgap AlGaN Polarization-Graded FET with Ultra-thin Buffer Layer

We report on the design and demonstration of ultra-wide bandgap AlGaN polarization-graded field effect transistors with ultra-thin channels to enable excellent current density and high-frequency performance while significantly reducing thermal resistance. We use polarization-graded AlGaN layers and ultra-thin pseudomorphic AlGaN buffer layers to enable low thermal resistance and excellent structural quality. The polarization-graded field effect transistors (PolFETs) demonstrated here show Imax over 800mA/mm and current/power gain cutoff frequency (fT/fmax) of 26/28 GHz. Small signal modeling and analysis were used to determine parasitic/transit delays, and gate-resistance thermometry was implemented to thermally characterize AlGaN PolFET and benchmark against state-of-the-art AlGaN HEMTs. The ultra-thin AlGaN PolFET showed thermal resistance of 12 K.mm/W, representing a significant reduction from typical AlGaN transistors. These results show state-of-art combination of high current density, excellent fT-LG product for ultra-wide bandgap AlGaN transistors, and superior thermal performance, and highlight the promise of AlGaN transistors for future RF and mm-wave applications.

physics.app-ph↗

arXiv2025

Broad-Range Tuning of Ferroelectric Switching of LaxBi1-xFeO3 Epitaxial Films via Digital Doping using Off-Axis Co-Sputtering

To investigate the scope of ferroelectric behavior in La-substituted BiFeO3 films, LaxBi1-xFeO3 epitaxial films were synthesized using off-axis co-sputtering on SrTiO3(001) and DyScO3(110) substrates with a SrRuO3 bottom electrode layer. A digital-doping deposition method was used to enable precise control and continuous tuning of La concentration in high-quality LaxBi1-xFeO3 films across a wide range of x = 0.05-0.60, which was systematically investigated using piezoresponse force microscopy. Robust and reversible out-of-plane ferroelectric switching has been observed up to x = 0.35, while films with x $\geq$ 0.37 exhibit no measurable ferroelectric behavior, indicating a sharp ferroelectric-to-paraelectric phase transition between x = 0.35 and 0.37. This represents the highest reported La concentration in LaxBi1-xFeO3 films that retains ferroelectric ordering, highlighting opportunities to engineer ferroelectric and multiferroic properties in complex oxide heterostructures.

cond-mat.mtrl-sci↗

arXiv2025

Barrier Electrostatics and Contact Engineering for Ultra-Wide Bandgap AlGaN HFETs

We report ultra-wide bandgap (UWBG) AlGaN heterostructure field-effect transistors (HFETs) exhibiting a high breakdown field (> 5.3 MV/cm) and a low contact resistance (~1.55 {\Omega}mm), tailored for high-power radiofrequency applications. A split-doped barrier architecture, employing two distinct doping concentrations, is shown to enhance both the breakdown field and contact resistance. This design enables a state-of-the-art combination of maximum drain current (487 mA/mm) and breakdown field, along with a high cutoff frequency of 7.2 GHz. These results demonstrate a viable pathway to push device performance toward the material limits while minimizing contact resistance in UWBG AlGaN HFETs, paving the way for next-generation high-power, high-frequency applications.

cond-mat.mtrl-sci↗

arXiv2025

High Breakdown Electric Field (> 5 MV/cm) in UWBG AlGaN Transistors

We report on the design and demonstration of ultra-wide bandgap (UWBG) AlGaN-channel metal-insulator heterostructure field effect transistors (HEFTs) for high-power, high-frequency applications. We find that the integration of gate dielectrics and field plates greatly improves the breakdown field in these devices, with state-of-art average breakdown field of 5.3 MV/cm (breakdown voltage > 260 V) with an associated maximum current density of 342 mA/mm, and cut-off frequency of 9.1 GHz. Furthermore, low trap-related impact was observed from minimal gate and drain lag estimated from pulsed I-V characteristics. The reported results provide the potential of UWBG AlGaN HEFTs for the next generation high-power radio frequency applications.

cond-mat.mtrl-sci↗

arXiv2025

Energy Bands and Breakdown Characteristics in Al2O3/UWBG AlGaN Heterostructures

We report on energy bands and breakdown characteristics of Al2O3 dielectrics on ultra-wide bandgap (UWBG) AlGaN heterostructures. Metal-dielectric-semiconductor structures are important to sustain high fields needed for future high-performance UWBG transistors. Using systematic experiments, we determined the fixed charge density (> 1013 cm-2), the dielectric/interface, and electric fields in the oxide of under flat-band conditions in the semiconductor. Low gate-to-drain leakage current of up to 5 x 10-7 A/cm2 were obtained in the metal-oxide-semiconductor structures. In lateral metal-semiconductor-insulator test structures, breakdown voltage exceeding 1 kV was obtained with a channel sheet charge density of 1.27 x 1013 cm-2. The effective peak electric field and average breakdown field were estimated to be > 4.27 MV/cm and 1.99 MV/cm, respectively. These findings demonstrate the potential of Al2O2 integration for enhancing the breakdown performance of UWBG AlGaN HEMTs.

cond-mat.mtrl-sci↗

arXiv2025

Impact of Quantum Well Thickness on Efficiency Loss in InGaN/GaN LEDs: Challenges for Thin-Well Designs

We investigate the impact of quantum well (QW) thickness on efficiency loss in c-plane InGaN/GaN LEDs using a small-signal electroluminescence (SSEL) technique. Multiple mechanisms related to efficiency loss are independently examined, including injection efficiency, carrier density vs. current density relationship, phase space filling (PSF), quantum confined stark effect (QCSE), and Coulomb enhancement. An optimal QW thickness of around 2.7 nm in these InGaN/GaN LEDs was determined for quantum wells having constant In composition. Despite better control of deep-level defects and lower carrier density at a given current density, LEDs with thin QWs still suffer from an imbalance of enhancement effects on the radiative and intrinsic Auger-Meitner recombination coefficients. The imbalance of enhancement effects results in a decline in internal quantum efficiency (IQE) and radiative efficiency with decreasing QW thickness at low current density in LEDs with QW thicknesses below 2.7 nm. We also investigate how LED modulation bandwidth varies with quantum well thickness, identifying the key trends and their implications for device performance.

physics.app-ph↗

arXiv2025

Electrical and Structural Properties of In-Situ MOCVD Grown Al$_2$O$_3$/$\beta$-Ga$_2$O$_3$ and Al$_2$O$_3$/$\beta$-(Al$_x$Ga$_{1-x}$)$_2$O$_3$ MOSCAPs

This study investigates the electrical and structural properties of MOSCAPs with in-situ MOCVD-grown Al$_2$O$_3$ dielectrics on (010) $\beta$-Ga$_2$O$_3$ and $\beta$-(Al$_x$Ga$_{1-x}$)$_2$O$_3$ films. The Al$_2$O$_3$/$\beta$-Ga$_2$O$_3$ MOSCAPs showed a strong dependence on Al$_2$O$_3$ deposition temperature. At 900$^\circ$C, reduced voltage hysteresis ($\sim$0.3 V) and improved reverse breakdown voltage (74.5 V) were observed, with breakdown fields of 5.01 MV/cm in Al$_2$O$_3$ and 4.11 MV/cm in $\beta$-Ga$_2$O$_3$. At 650$^\circ$C, higher hysteresis ($\sim$3.44 V) and lower reverse breakdown voltage (38.8 V) were observed, with breakdown fields of 3.69 MV/cm in Al$_2$O$_3$ and 2.87 MV/cm in $\beta$-Ga$_2$O$_3$. However, forward breakdown fields improved from 5.62 MV/cm (900$^\circ$C) to 7.25 MV/cm (650$^\circ$C). STEM revealed improved crystallinity and sharper interfaces at 900$^\circ$C, enhancing reverse breakdown performance. For Al$_2$O$_3$/$\beta$-(Al$_x$Ga$_{1-x}$)$_2$O$_3$ MOSCAPs, increasing Al composition ($x$ = 5.5\% to 9.2\%) reduced carrier concentration and improved reverse breakdown fields from 2.55 to 2.90 MV/cm in $\beta$-(Al$_x$Ga$_{1-x}$)$_2$O$_3$ and 2.41 to 3.13 MV/cm in Al$_2$O$_3$. Forward breakdown fields in Al$_2$O$_3$ improved from 5.0 to 5.4 MV/cm as Al composition increased. STEM confirmed compositional homogeneity and excellent stoichiometry of Al$_2$O$_3$ and $\beta$-(Al$_x$Ga$_{1-x}$)$_2$O$_3$ layers. These findings highlight the robust electrical performance, high breakdown fields, and structural quality of Al$_2$O$_3$/$\beta$-Ga$_2$O$_3$ and Al$_2$O$_3$/$\beta$-(Al$_x$Ga$_{1-x}$)$_2$O$_3$ MOSCAPs for high-power applications.

physics.app-ph↗

arXiv2024

Heterostructure and Interfacial Engineering for Low-Resistance Contacts to Ultra-Wide Bandgap AlGaN

We report on the heterostructure and interfacial engineering of metalorganic chemical vapor deposition (MOCVD) grown reverse-graded contacts to ultra-wide bandgap AlGaN. A record low contact resistivity of 1.4 x 10-6 Ohm.cm2 was reported on an Al0.82Ga0.18N metal semiconductor field effect transistor (MESFET) by compositionally grading the contact layer from Al0.85Ga0.15N to Al0.14Ga0.86N with degenerate doping and proper interfacial engineering considering bandgap-narrowing-induced band offset between channel and contact layer. This represents orders-of-magnitude of lower contact resistivity than that obtained in similar MOCVD-grown structures. A detailed, layer-by-layer analysis of the reverse graded contact and TCAD simulation of the bandgap narrowing effect highlighted that the reverse graded contact layer itself is extremely conductive and interfacial resistance due to bandgap-narrowing-induced barrier between contact and channel dominates the contact resistance.

cond-mat.mtrl-sci↗

arXiv2024

Selective-injection GaN Heterojunction Bipolar Transistors with 275 kA/cm$^2$ Current Density

We design and demonstrate selective injection GaN heterojunction bipolar transistors that utilize a patterned base for selective injection of electrons from the emitter. The design maneuvers minority carrier injection through a thin p-GaN base region, while the majority carrier holes for base current are injected from thick p-GaN regions adjacent to the thin p-GaN base. The design is realized using a regrowth emitter approach with SiO$_2$ as a spacer between the emitter layer and the thick p-GaN base contact regions. The fabricated device demonstrated state-of-art output current density (I$_{C, max}$) ~275 kA/cm$^2$ with a current gain ($β$) of 9, and 17 for the planar HBT design (I$_{C, max}$ =150 kA/cm$^2$). The reported results highlight the potential of the selective injection design to overcome the persistent GaN HBT design tradeoff between base resistance and current gain, paving the way for next-generation radio frequency and mm-Wave applications.

physics.app-ph↗

arXiv2024

Active Interface Characteristics of Heterogeneously Integrated GaAsSb/Si Photodiodes

There is increased interest in the heterogeneous integration of various compound semiconductors with Si for a variety of electronic and photonic applications. This paper focuses on integrating GaAsSb (with absorption in the C-band at 1550nm) with silicon to fabricate photodiodes, leveraging epitaxial layer transfer (ELT) methods. Two ELT techniques, epitaxial lift-off (ELO) and macro-transfer printing (MTP), are compared for transferring GaAsSb films from InP substrates to Si, forming PIN diodes. Characterization through atomic force microscopy (AFM), and transmission electron microscopy (TEM) exhibits a high-quality, defect-free interface. Current-voltage (IV) measurements and capacitance-voltage (CV) analysis validate the quality and functionality of the heterostructures. Photocurrent measurements at room temperature and 200 K demonstrate the device's photo-response at 1550 nm, highlighting the presence of an active interface.

physics.app-ph↗

arXiv2024

Tunnel Junction-Enabled Monolithically Integrated GaN Micro-Light Emitting Transistor

GaN/InGaN microLEDs are a very promising technology for next generation displays. Switching control transistors and their integration are key components in achieving high-performance, efficient displays. Monolithic integration of microLEDs with GaN switching devices provides an opportunity to control microLED output power with capacitive (voltage) control rather than current controlled schemes. This approach can greatly reduce system complexity for the driver circuit arrays while maintaining device opto-electronic performance. In this work, we demonstrate a 3-terminal GaN micro-light emitting transistor that combines a GaN/InGaN blue tunneling-based microLED with a GaN n-channel FET. The integrated device exhibits excellent gate control, drain current control and optical emission control. This work provides a promising pathway for future monolithic integration of GaN FETs with microLED to enable fast switching high efficiency microLED display and communication systems.

physics.app-ph↗

arXiv2024

Design and Simulation of a III-Nitride Light Emitting Transistor

This paper describes the design and characteristics of monolithically integrated three-terminal gated III-Nitride light emitting diodes (LEDs) devices. The impact of channel doping and thickness on the voltage penalty of the transistor-LED hybrid device is analyzed, and it is shown that with appropriate design, low voltage drop can be realized across integrated gated LED structures. The impact of device design on the switching charge is investigated, and it is shown that the adoption of an integrated LED/transistor structure can reduce the switching charge necessary for operation of a switched LED display device by an order of magnitude when compared with stand-alone light-emitting diodes.

physics.app-ph↗